基于AMBA总线协议的Verilog语言模型实现
一、AMBA总线协议模型架构
核心模块组成
| 协议 | 主要模块 | 功能描述 |
|---|---|---|
| AHB | 主控制器/从设备 | 突发传输控制、仲裁逻辑 |
| AXI | 主接口/从接口/通道管理 | 多通道数据流、乱序完成处理 |
| APB | 主设备/从设备/桥接器 | 寄存器访问、两阶段传输 |
二、AHB总线Verilog实现
2.1 模块接口定义
module ahb_master #(parameter ADDR_WIDTH = 32,parameter DATA_WIDTH = 32
)(input wire HCLK,input wire HRESETn,output reg [ADDR_WIDTH-1:0] HADDR,output reg [DATA_WIDTH-1:0] HWDATA,input wire [DATA_WIDTH-1:0] HRDATA,output reg HWRITE,output reg [1:0] HTRANS,input wire HREADY,output reg [2:0] HBURST
);// 状态机定义typedef enum logic [2:0] {IDLE,BUSY,NONSEQ,SEQ,RETRY} ahb_state_t;ahb_state_t current_state, next_state;// 传输控制逻辑always_ff @(posedge HCLK or negedge HRESETn) beginif (!HRESETn) current_state <= IDLE;else current_state <= next_state;end// 状态转移逻辑always_comb begincase(current_state)IDLE: next_state = (HTRANS != IDLE) ? NONSEQ : IDLE;NONSEQ: next_state = (HREADY) ? SEQ : NONSEQ;SEQ: next_state = (HREADY) ? SEQ : NONSEQ;RETRY: next_state = (HREADY) ? IDLE : RETRY;default: next_state = IDLE;endcaseend
endmodule
2.2 关键实现技术
-
突发传输控制：通过HBURST信号生成连续地址
always_ff @(posedge HCLK) beginif (HTRANS == NONSEQ) beginHADDR <= target_addr;end else if (HTRANS == SEQ) beginHADDR <= HADDR + (1 << AWIDTH);end end -
仲裁逻辑：多主设备竞争总线控制权
assign HGRANT = (arb_priority == MASTER_ID) ? 1 : 0;
三、AXI总线Verilog实现
3.1 通道信号定义
// 写地址通道
output reg [31:0] AWADDR;
output reg [7:0] AWLEN;
output reg [2:0] AWSIZE;
output reg AWVALID;// 写数据通道
output reg [31:0] WDATA;
output reg [3:0] WSTRB;
output reg WVALID;// 写响应通道
input wire [1:0] BRESP;
input wire BVALID;// 读地址通道
output reg [31:0] ARADDR;
output reg [7:0] ARLEN;
output reg [2:0] ARSIZE;
output reg ARVALID;// 读数据通道
input wire [31:0] RDATA;
input wire [1:0] RRESP;
input wire RVALID;
3.2 状态机实现
typedef enum logic [3:0] {IDLE,WRITE_ADDR,WRITE_DATA,WRITE_RESP,READ_ADDR,READ_DATA,DONE
} axi_state_t;axi_state_t state, next_state;always_ff @(posedge ACLK or negedge ARESETn) beginif (!ARESETn) state <= IDLE;else state <= next_state;
endalways_comb begincase(state)IDLE: next_state = (aw_valid) ? WRITE_ADDR : IDLE;WRITE_ADDR: next_state = (aw_ready) ? WRITE_DATA : WRITE_ADDR;WRITE_DATA: next_state = (w_valid) ? WRITE_DATA : WRITE_RESP;WRITE_RESP: next_state = (b_valid) ? DONE : WRITE_RESP;// 其他状态转换逻辑...endcase
end
四、APB总线Verilog实现
4.1 主设备核心逻辑
module apb_master #(parameter ADDR_WIDTH = 32,parameter DATA_WIDTH = 32
)(input wire PCLK,input wire PRESETn,output reg PSEL,output reg PENABLE,output reg PWRITE,output reg [ADDR_WIDTH-1:0] PADDR,output reg [DATA_WIDTH-1:0] PWDATA,input wire [DATA_WIDTH-1:0] PRDATA,input wire PREADY,input wire PSLVERR
);typedef enum logic [1:0] {IDLE,SETUP,ACCESS} apb_state_t;apb_state_t state, next_state;always_ff @(posedge PCLK or negedge PRESETn) beginif (!PRESETn) state <= IDLE;else state <= next_state;endalways_comb begincase(state)IDLE: beginif (transfer_pending) next_state = SETUP;else next_state = IDLE;endSETUP: next_state = ACCESS;ACCESS: beginif (PREADY) next_state = IDLE;else next_state = ACCESS;endendcaseendalways_ff @(posedge PCLK) begincase(state)SETUP: beginPSEL <= 1;PADDR <= target_addr;PWRITE <= write_en;PWDATA <= write_data;endACCESS: beginPENABLE <= 1;endendcaseend
endmodule
五、验证与调试技术
5.1 测试平台设计
module tb_ahb_master();reg HCLK = 0;reg HRESETn = 0;wire [31:0] HADDR;wire [31:0] HWDATA;reg [31:0] HRDATA;reg HWRITE;reg [1:0] HTRANS;wire HREADY;reg [2:0] HBURST;ahb_master uut (.HCLK(HCLK),.HRESETn(HRESETn),.HADDR(HADDR),.HWDATA(HWDATA),.HRDATA(HRDATA),.HWRITE(HWRITE),.HTRANS(HTRANS),.HREADY(HREADY),.HBURST(HBURST));initial beginHRESETn = 0; #10;HRESETn = 1;HTRANS = 2'b01; // NONSEQHADDR = 32'h1000;HWDATA = 32'hDEADBEEF;HWRITE = 1;#20;HTRANS = 2'b00; // IDLE#100;$finish;endalways #5 HCLK = ~HCLK;
endmodule
5.2 性能验证方法
-
时序分析：使用静态时序分析工具验证关键路径
report_timing -delay_type max -sort_by group -
功耗分析：通过仿真获取动态/静态功耗数据
initial begin$display("Dynamic Power: %.2f mW", power_dynamic);$display("Leakage Power: %.2f mW", power_leakage); end
参考代码 AMBA总线的Verilog语言模型 www.youwenfan.com/contentcsh/56343.html
通过上述模型实现，开发者可构建符合AMBA标准的总线系统。建议结合具体应用场景选择协议类型，并通过仿真验证确保时序正确性和功能完整性。