当前位置：首页 > news >正文

20250726让荣品的PRO-RK3566开发板使用TF卡启动

news 2025/7/27 5:29:10

20250726让荣品的PRO-RK3566开发板使用TF卡启动
2025/7/26 8:58

缘起：需要升级荣品的PRO-RK3566核心板的底板上的FPGA程序。
由于没有使用RK809的电量计功能，板子一上电就会被关机！^_

于是给生产线制作了一张TF卡/启动卡，插到底板上。
上电的时候就会进Buildroot/Linux系统，而不是关机！

写卡工具使用的是SDK自带的：SDDiskTool_v1.76.zip
Z:\source\tools\windows\SDDiskTool_v1.76.zip

写卡之前，可以使用 SD Card Formatter 重新格式化一下TF卡。
如果你的TF卡以前制作过各种启动卡，使用 SD Card Formatter 可以完美的格式化/还原。
是SD协会官方出品，性能可靠/稳定看得见！^_

制作卡启动的TF卡制作完成之后，你会发现很多打不开的磁盘。
这是正常现象。因为是LINUX分区：比如ext4格式/swap格式等。
在WIN10/WIN11下打不开是正常现象。

启动的完整LOG：

[BEGIN] 2025/7/26 9:40:24
DDR V1.14 b1f29a2a6f typ 22/09/02-16:40:04
ln
ddrconfig:0
LP4 MR14:0x4d
LPDDR4, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS=1 Die BW=16 Size=4096MB
tdqss: cs0 dqs0: -24ps, dqs1: -96ps, dqs2: -72ps, dqs3: -120ps,

change to: 324MHz
PHY drv:clk:38,ca:38,DQ:30,odt:0
vrefinner:41%, vrefout:41%
dram drv:40,odt:0
clk skew:0x62

change to: 528MHz
PHY drv:clk:38,ca:38,DQ:30,odt:0
vrefinner:41%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58

change to: 780MHz
PHY drv:clk:38,ca:38,DQ:30,odt:0
vrefinner:41%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58

change to: 1056MHz(final freq)
PHY drv:clk:38,ca:38,DQ:30,odt:60
vrefinner:16%, vrefout:29%
dram drv:40,odt:80
vref_ca:00000068
clk skew:0x2c
cs 0:
the read training result:
DQS0:0x37, DQS1:0x39, DQS2:0x35, DQS3:0x39,
min : 0x7 0x5 0x3 0x3 0x3 0x3 0x1 0x1 , 0x3 0x5 0x9 0x4 0x1 0x3 0x6 0x2 ,
0x8 0x7 0x6 0x4 0x3 0x4 0x4 0x2 , 0xa 0x6 0x8 0x5 0x6 0x5 0x7 0x1 ,
mid :0x25 0x21 0x20 0x20 0x21 0x20 0x1f 0x1e ,0x21 0x23 0x27 0x22 0x1f 0x22 0x23 0x1f ,
0x26 0x24 0x22 0x21 0x20 0x21 0x20 0x1e ,0x27 0x22 0x24 0x22 0x22 0x21 0x24 0x1e ,
max :0x44 0x3d 0x3e 0x3e 0x3f 0x3d 0x3e 0x3c ,0x3f 0x41 0x45 0x40 0x3e 0x41 0x41 0x3c ,
0x45 0x42 0x3e 0x3e 0x3d 0x3e 0x3d 0x3b ,0x44 0x3f 0x41 0x40 0x3f 0x3e 0x41 0x3c ,
range:0x3d 0x38 0x3b 0x3b 0x3c 0x3a 0x3d 0x3b ,0x3c 0x3c 0x3c 0x3c 0x3d 0x3e 0x3b 0x3a ,
0x3d 0x3b 0x38 0x3a 0x3a 0x3a 0x39 0x39 ,0x3a 0x39 0x39 0x3b 0x39 0x39 0x3a 0x3b ,
the write training result:
DQS0:0x29, DQS1:0x20, DQS2:0x23, DQS3:0x1c,
min :0x4f 0x4f 0x4f 0x50 0x4e 0x4e 0x4d 0x50 0x4f ,0x43 0x45 0x4a 0x46 0x43 0x47 0x48 0x47 0x45 ,
0x4c 0x4b 0x4a 0x4a 0x49 0x49 0x4b 0x4b 0x4b ,0x46 0x43 0x45 0x45 0x45 0x43 0x46 0x45 0x42 ,
mid :0x6c 0x6b 0x6b 0x6c 0x69 0x6a 0x68 0x6b 0x6b ,0x5f 0x60 0x66 0x61 0x5e 0x61 0x62 0x63 0x60 ,
0x68 0x67 0x65 0x65 0x64 0x64 0x65 0x64 0x67 ,0x60 0x5d 0x5f 0x5e 0x5e 0x5d 0x60 0x5e 0x5d ,
max :0x89 0x87 0x88 0x88 0x85 0x86 0x84 0x86 0x87 ,0x7c 0x7b 0x83 0x7d 0x7a 0x7c 0x7d 0x80 0x7c ,
0x84 0x83 0x81 0x81 0x80 0x80 0x80 0x7d 0x83 ,0x7b 0x77 0x7a 0x78 0x77 0x78 0x7b 0x78 0x78 ,
range:0x3a 0x38 0x39 0x38 0x37 0x38 0x37 0x36 0x38 ,0x39 0x36 0x39 0x37 0x37 0x35 0x35 0x39 0x37 ,
0x38 0x38 0x37 0x37 0x37 0x37 0x35 0x32 0x38 ,0x35 0x34 0x35 0x33 0x32 0x35 0x35 0x33 0x36 ,
CA Training result:
cs:0 min :0x44 0x43 0x3b 0x38 0x3b 0x37 0x3d ,0x44 0x3f 0x3b 0x37 0x3a 0x32 0x3a ,
cs:0 mid :0x82 0x82 0x78 0x78 0x78 0x76 0x6c ,0x82 0x7f 0x77 0x77 0x78 0x73 0x68 ,
cs:0 max :0xc0 0xc2 0xb5 0xb9 0xb5 0xb6 0x9b ,0xc0 0xc0 0xb4 0xb7 0xb6 0xb5 0x97 ,
cs:0 range:0x7c 0x7f 0x7a 0x81 0x7a 0x7f 0x5e ,0x7c 0x81 0x79 0x80 0x7c 0x83 0x5d ,
out
U-Boot SPL board init
U-Boot SPL 2017.09-gaaca6ffec1-211203 #zzz (Dec 03 2021 - 18:42:16)
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
Magic is incorrect.
Error validating A/B metadata from disk. Resetting and writing new A/B metadata to disk.
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(b5946ac63d...) + OK
## Checking uboot 0x00a00000 ... sha256(6be14b813a...) + OK
## Checking fdt 0x00b47c68 ... sha256(036cca5880...) + OK
## Checking atf-2 0xfdcc1000 ... sha256(b8dca786b4...) + OK
## Checking atf-3 0x0006b000 ... sha256(2f91089eb7...) + OK
## Checking atf-4 0xfdcce000 ... sha256(86ef885748...) + OK
## Checking atf-5 0xfdcd0000 ... sha256(0b2b146c60...) + OK
## Checking atf-6 0x00069000 ... sha256(a9a1e63bef...) + OK
## Checking optee 0x08400000 ... sha256(6c92ef6a0e...) + OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 401.661 ms

INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-645-g8cea6ab0b:cl, fwver: v1.44
NOTICE: BL31: Built : 16:36:43, Sep 19 2023
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: pmu v1 is valid 220114
INFO: l3 cache partition cfg-0
INFO: dfs DDR fsp_param[0].freq_mhz= 1056MHz
INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO: dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO: dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
I/TC:
I/TC: OP-TEE version: 3.13.0-743-gb5340fd65 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #5 Mon Aug 28 15:15:17 CST 2023 aarch64
I/TC: Primary CPU initializing
E/TC:0 0 hal_algo_version_init:296 CRYPTO_CRYPTO_VERSION_NEW no support. Skip all algo mode check.
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9

U-Boot 2017.09 (Jul 11 2025 - 10:58:04 +0800)

Model: Rockchip RK3568 Evaluation Board
MPIDR: 0x81000000
PreSerial: 2, raw, 0xfe660000
DRAM: 3.7 GiB
Sysmem: init
Relocation Offset: ed217000
Relocation fdt: eb9f8948 - eb9fece0
CR: M/C/I
Using default environment

optee api revision: 2.0
no mmc device at slot 1
Repair the backup gpt table OK!
dwmmc@fe2b0000: 1 (SD), dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 1
MMC1: Legacy, 52Mhz
PartType: EFI
TEEC: Waring: Could not find security partition
DM: v1
boot mode: None
RESC: 'boot', blk@0x0001c65d
resource: sha256+
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
I2c0 speed: 100000Hz
PMIC: RK8090 (on=0x40, off=0x00)
vdd_logic init 950000 uV
vdd_gpu init 900000 uV
vdd_npu init 900000 uV
vsel-gpios- not found! Error: -2
vdd_cpu init 1000000 uV
io-domain: OK
INFO: ddr dmc_fsp already initialized in loader.
Could not find baseparameter partition
Model: pro-rk3566
MPIDR: 0x81000000
ethaddr = b2:52:ef:7c:52:a8
eth1addr = b2:e1:71:d7:7c:8c
eth2addr = 02:f8:69:4b:03:18
eth3addr = 46:66:c5:50:26:68
rp_power not have children !
rp_power have node!
rp_power: pwr_5v_3v3 gpio set output
rp_power: led gpio function is 3, not realize!
rp_power: usb_pwr gpio set output
rp_power: otg_pwr gpio set output
rp_power: usb_rst gpio set output
rp_power: spk_en gpio function get error, set gpio default dir to output
rp_power: spk_en gpio get error
rp_power: spk_mute gpio set output
rp_power: usb_mode gpio set output
rp_power: Equipment_EN gpio set output
Rockchip UBOOT DRM driver version: v1.0.1
VOP have 1 active VP
vp0 have layer nr:6[0 2 4 1 3 5 ], primary plane: 4
vp1 have layer nr:0[], primary plane: 0
vp2 have layer nr:0[], primary plane: 0
hdmi@fe0a0000 disconnected
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
apll 1104000 KHz
dpll 528000 KHz
gpll 1188000 KHz
cpll 1000000 KHz
npll 1200000 KHz
vpll 24000 KHz
hpll 24000 KHz
ppll 200000 KHz
armclk 1104000 KHz
aclk_bus 150000 KHz
pclk_bus 100000 KHz
aclk_top_high 500000 KHz
aclk_top_low 400000 KHz
hclk_top 150000 KHz
pclk_top 100000 KHz
aclk_perimid 300000 KHz
hclk_perimid 150000 KHz
pclk_pmu 100000 KHz
Net: eth1: ethernet@fe010000
Hit key to stop autoboot('CTRL+C'): 0
ANDROID: reboot reason: "(none)"
Not AVB images, AVB skip
No valid android hdr
Android image load failed
Android boot failed, error -1.
## Booting FIT Image at 0xe8f2bf00 with size 0x028cba00
Fdt Ramdisk skip relocation
## Loading kernel from FIT Image at e8f2bf00 ...
Using 'conf' configuration
## Verified-boot: 0
Trying 'kernel' kernel subimage
Description: unavailable
Type: Kernel Image
Compression: uncompressed
Data Start: 0xe8f55f00
Data Size: 42605056 Bytes = 40.6 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x00280000
Entry Point: 0x00280000
Hash algo: sha256
Hash value: e80143e08e6530852192e34c9832cc35cbf815029b09e1d027a621a851767513
Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at e8f2bf00 ...
Using 'conf' configuration
Trying 'fdt' fdt subimage
Description: unavailable
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0xe8f2c700
Data Size: 169955 Bytes = 166 KiB
Architecture: AArch64
Load Address: 0x08300000
Hash algo: sha256
Hash value: aa03975c23e9ca53e194f3eaa8cf4f5c8980d2baebbd1e73626a72c309d954ca
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x08300000 to 0x08300000
Booting using the fdt blob at 0x08300000
Loading Kernel Image from 0xe8f55f00 to 0x00280000 ... OK
kernel loaded at 0x00280000, end = 0x02b21a00
Using Device Tree in place at 0000000008300000, end 000000000832c7e2
vp0, plane_mask:0x3f, primary-id:4, curser-id:-1
vp1, plane_mask:0x0, primary-id:0, curser-id:-1
vp2, plane_mask:0x0, primary-id:0, curser-id:-1
WARNING: could not set reg FDT_ERR_BADOFFSET.
## reserved-memory:
drm-logo@00000000: addr=edf00000 size=106000
drm-cubic-lut@00000000: addr=eff00000 size=8000
ramoops@110000: addr=110000 size=f0000
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
== DO RELOCATE == Kernel from 0x00280000 to 0x00200000
Total: 4661.372/4795.550 ms

Starting kernel ...

[ 4.805968] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 4.805997] Linux version 5.10.198 (rootroot@rootroot-X99-Turbo) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 10.3.1 20210621, GNU ld (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 2.36.1.20210621) #1 SMP Tue Jul 8 09:38:35 CST 2025
[ 4.807836] random: crng init done
[ 4.811917] Machine model: pro-rk3566
[ 4.855626] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options '')
[ 4.907805] printk: bootconsole [uart8250] enabled
[ 4.914229] efi: UEFI not found.
[ 4.974998] Zone ranges:
[ 4.977783] DMA [mem 0x0000000000200000-0x00000000efffffff]
[ 4.984563] DMA32 empty
[ 4.987715] Normal empty
[ 4.990866] Movable zone start for each node
[ 4.995542] Early memory node ranges
[ 4.999456] node 0: [mem 0x0000000000200000-0x00000000083fffff]
[ 5.006326] node 0: [mem 0x0000000009400000-0x00000000efffffff]
[ 5.013200] Initmem setup node 0 [mem 0x0000000000200000-0x00000000efffffff]
[ 5.050797] cma: Reserved 16 MiB at 0x00000000ee400000
[ 5.056520] psci: probing for conduit method from DT.
[ 5.062066] psci: PSCIv1.1 detected in firmware.
[ 5.067124] psci: Using standard PSCI v0.2 function IDs
[ 5.072854] psci: Trusted OS migration not required
[ 5.078200] psci: SMC Calling Convention v1.2
[ 5.083380] percpu: Embedded 31 pages/cpu s88344 r8192 d30440 u126976
[ 5.090554] Detected VIPT I-cache on CPU0
[ 5.094990] CPU features: detected: GIC system register CPU interface
[ 5.102051] CPU features: detected: Virtualization Host Extensions
[ 5.108831] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 5.116486] alternatives: patching kernel code
[ 5.123571] Built 1 zonelists, mobility grouping on. Total pages: 963080
[ 5.131021] Kernel command line: storagemedia=sd androidboot.storagemedia=sd androidboot.mode=normal androidboot.verifiedbootstate=orange rw rootwait earlycon=uart8250,mmio32,0xfe660000 console=ttyFIQ0 root=PARTUUID=614e0000-0000 androidboot.fwver=bl31-v1.44,uboot-07/11/2025
[ 5.159097] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 5.168273] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 5.176766] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 5.235935] Memory: 3777056K/3913728K available (22208K kernel code, 3846K rwdata, 7876K rodata, 7552K init, 878K bss, 120288K reserved, 16384K cma-reserved)
[ 5.251515] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 5.258711] ftrace: allocating 67078 entries in 263 pages
[ 5.353835] ftrace: allocated 263 pages with 4 groups
[ 5.359733] rcu: Hierarchical RCU implementation.
[ 5.364896] rcu:    RCU event tracing is enabled.
[ 5.369860] rcu:    RCU dyntick-idle grace-period acceleration is enabled.
[ 5.377205] rcu:    RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 5.384362]    Rude variant of Tasks RCU enabled.
[ 5.389324]    Tracing variant of Tasks RCU enabled.
[ 5.394572] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[ 5.402871] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 5.415220] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 5.422861] GICv3: GIC: Using split EOI/Deactivate mode
[ 5.428601] GICv3: 320 SPIs implemented
[ 5.432801] GICv3: 0 Extended SPIs implemented
[ 5.437703] GICv3: Distributor has no Range Selector support
[ 5.443913] GICv3: 16 PPIs implemented
[ 5.448055] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
[ 5.455702] ITS [mem 0xfd440000-0xfd45ffff]
[ 5.460352] ITS@0x00000000fd440000: allocated 8192 Devices @2e00000 (indirect, esz 8, psz 64K, shr 0)
[ 5.470495] ITS@0x00000000fd440000: allocated 32768 Interrupt Collections @2e10000 (flat, esz 2, psz 64K, shr 0)
[ 5.481658] ITS: using cache flushing for cmd queue
[ 5.487407] GICv3: using LPI property table @0x0000000002e20000
[ 5.494013] GIC: using cache flushing for LPI property table
[ 5.500221] GICv3: CPU0: using allocated LPI pending table @0x0000000002e30000
[ 5.508202] rcu:    Offload RCU callbacks from CPUs: (none).
[ 5.543225] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 5.549922] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 5.561758] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 5.571622] Console: colour dummy device 80x25
[ 5.576544] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 5.587818] pid_max: default: 32768 minimum: 301
[ 5.592979] LSM: Security Framework initializing
[ 5.598107] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 5.606238] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 5.616400] rcu: Hierarchical SRCU implementation.
[ 5.622490] Platform MSI: interrupt-controller@fd440000 domain created
[ 5.630149] PCI/MSI: /interrupt-controller@fd400000/interrupt-controller@fd440000 domain created
[ 5.640147] EFI services will not be available.
[ 5.645459] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
[ 5.658771] Detected VIPT I-cache on CPU1
[ 5.658802] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
[ 5.658823] GICv3: CPU1: using allocated LPI pending table @0x0000000002e40000
[ 5.658878] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[ 5.667233] Detected VIPT I-cache on CPU2
[ 5.667259] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
[ 5.667279] GICv3: CPU2: using allocated LPI pending table @0x0000000002e50000
[ 5.667318] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[ 5.675620] Detected VIPT I-cache on CPU3
[ 5.675645] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000
[ 5.675662] GICv3: CPU3: using allocated LPI pending table @0x0000000002e60000
[ 5.675700] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[ 5.675794] smp: Brought up 1 node, 4 CPUs
[ 5.761905] SMP: Total of 4 processors activated.
[ 5.767067] CPU features: detected: Privileged Access Never
[ 5.773178] CPU features: detected: LSE atomic instructions
[ 5.779291] CPU features: detected: User Access Override
[ 5.785117] CPU features: detected: 32-bit EL0 Support
[ 5.790753] CPU features: detected: Common not Private translations
[ 5.797627] CPU features: detected: RAS Extension Support
[ 5.803549] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 5.812999] CPU features: detected: CRC32 instructions
[ 5.818634] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 5.826272] CPU features: detected: RCpc load-acquire (LDAPR)
[ 5.867196] CPU: All CPU(s) started at EL2
[ 5.873313] devtmpfs: initialized
[ 5.899332] Registered cp15_barrier emulation handler
[ 5.904913] Registered setend emulation handler
[ 5.910068] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 5.920777] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 5.928905] pinctrl core: initialized pinctrl subsystem
[ 5.935196] DMI not present or invalid.
[ 5.939698] NET: Registered protocol family 16
[ 5.946207] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[ 5.954128] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 5.962737] audit: initializing netlink subsys (disabled)
[ 5.968843] audit: type=2000 audit(0.249:1): state=initialized audit_enabled=0 res=1
[ 5.970942] Registered FIQ tty driver
[ 5.981769] thermal_sys: Registered thermal governor 'fair_share'
[ 5.981773] thermal_sys: Registered thermal governor 'step_wise'
[ 5.988467] thermal_sys: Registered thermal governor 'user_space'
[ 5.995057] thermal_sys: Registered thermal governor 'power_allocator'
[ 6.002059] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[ 6.018074] cpuidle: using governor menu
[ 6.022684] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 6.030250] ASID allocator initialised with 65536 entries
[ 6.038498] ramoops: dmesg-0   0x20000@0x0000000000110000
[ 6.044271] ramoops: console   0x80000@0x0000000000130000
[ 6.050019] ramoops: pmsg   0x50000@0x00000000001b0000
[ 6.055825] printk: console [ramoops-1] enabled
[ 6.060799] pstore: Registered ramoops as persistent store backend
[ 6.067582] ramoops: using 0xf0000@0x110000, ecc: 0
[ 6.109563] rockchip-gpio fdd60000.gpio0: probed /pinctrl/gpio0@fdd60000
[ 6.117429] rockchip-gpio fe740000.gpio1: probed /pinctrl/gpio1@fe740000
[ 6.125220] rockchip-gpio fe750000.gpio2: probed /pinctrl/gpio2@fe750000
[ 6.133082] rockchip-gpio fe760000.gpio3: probed /pinctrl/gpio3@fe760000
[ 6.140893] rockchip-gpio fe770000.gpio4: probed /pinctrl/gpio4@fe770000
[ 6.148371] rockchip-pinctrl pinctrl: probed pinctrl
[ 6.231055] raid6: neonx8 gen() 2449 MB/s
[ 6.291135] raid6: neonx8 xor() 1944 MB/s
[ 6.351216] raid6: neonx4 gen() 2509 MB/s
[ 6.411291] raid6: neonx4 xor() 1926 MB/s
[ 6.471380] raid6: neonx2 gen() 2279 MB/s
[ 6.531452] raid6: neonx2 xor() 1762 MB/s
[ 6.591532] raid6: neonx1 gen() 1858 MB/s
[ 6.651614] raid6: neonx1 xor() 1418 MB/s
[ 6.711692] raid6: int64x8 gen() 1662 MB/s
[ 6.771779] raid6: int64x8 xor() 897 MB/s
[ 6.831858] raid6: int64x4 gen() 1798 MB/s
[ 6.891936] raid6: int64x4 xor() 966 MB/s
[ 6.952020] raid6: int64x2 gen() 1602 MB/s
[ 7.012094] raid6: int64x2 xor() 864 MB/s
[ 7.072174] raid6: int64x1 gen() 1161 MB/s
[ 7.132239] raid6: int64x1 xor() 586 MB/s
[ 7.136925] raid6: using algorithm neonx4 gen() 2509 MB/s
[ 7.142849] raid6: .... xor() 1926 MB/s, rmw enabled
[ 7.148296] raid6: using neon recovery algorithm
[ 7.154975] fiq_debugger fiq_debugger.0: IRQ fiq not found
[ 7.161133] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[ 7.167451] fiq_debugger_probe: could not install nmi irq handler
[[ 7.174228] printk: console [ttyFIQ0] enabled
7.174228] printk: console [ttyFIQ0] enabled
[ 7.183355] printk: bootconsole [[ 7.183355] printk: bootconsole [uart8250] disabled
uart8250] disabled
[ 7.193774] Registered fiq debugger ttyFIQ0
[ 7.194504] vcc3v3_sys: supplied by dc_12v
[ 7.194797] vcc5v0_sys: supplied by dc_12v
[ 7.195323] vcc3v3_lcd0_n: supplied by vcc3v3_sys
[ 7.195610] vcc3v3_lcd1_n: supplied by vcc3v3_sys
[ 7.196519] iommu: Default domain type: Translated
[ 7.200002] SCSI subsystem initialized
[ 7.200275] usbcore: registered new interface driver usbfs
[ 7.200329] usbcore: registered new interface driver hub
[ 7.200371] usbcore: registered new device driver usb
[ 7.200460] mc: Linux media interface: v0.10
[ 7.200489] videodev: Linux video capture interface: v2.00
[ 7.200574] pps_core: LinuxPPS API ver. 1 registered
[ 7.200583] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 7.200600] PTP clock support registered
[ 7.200641] EDAC MC: Ver: 3.0.0
[ 7.201575] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[ 7.201647] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[ 7.203794] Advanced Linux Sound Architecture Driver Initialized.
[ 7.204282] Bluetooth: Core ver 2.22
[ 7.204324] NET: Registered protocol family 31
[ 7.204332] Bluetooth: HCI device and connection manager initialized
[ 7.204345] Bluetooth: HCI socket layer initialized
[ 7.204355] Bluetooth: L2CAP socket layer initialized
[ 7.204374] Bluetooth: SCO socket layer initialized
[ 7.204729] rockchip-cpuinfo cpuinfo: SoC       : 35662000
[ 7.204741] rockchip-cpuinfo cpuinfo: Serial       : ba7f186fecbfe667
[ 7.205494] clocksource: Switched to clocksource arch_sys_counter
[ 7.647102] NET: Registered protocol family 2
[ 7.647386] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 7.649236] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 7.649299] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 7.649458] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
[ 7.649905] TCP: Hash tables configured (established 32768 bind 32768)
[ 7.650073] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 7.650134] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 7.650341] NET: Registered protocol family 1
[ 7.650916] RPC: Registered named UNIX socket transport module.
[ 7.650926] RPC: Registered udp transport module.
[ 7.650932] RPC: Registered tcp transport module.
[ 7.650938] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 7.651879] PCI: CLS 0 bytes, default 64
[ 7.654337] rockchip-thermal fe710000.tsadc: tsadc is probed successfully!
[ 7.655310] hw perfevents: enabled with armv8_cortex_a55 PMU driver, 7 counters available
[ 7.659536] Initialise system trusted keyrings
[ 7.659694] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 7.664684] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 7.665434] NFS: Registering the id_resolver key type
[ 7.665469] Key type id_resolver registered
[ 7.665500] Key type id_legacy registered
[ 7.665544] ntfs: driver 2.1.32 [Flags: R/O].
[ 7.665693] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 7.665921] fuse: init (API version 7.32)
[ 7.666296] SGI XFS with security attributes, no debug enabled
[ 7.698166] NET: Registered protocol family 38
[ 7.698193] xor: measuring software checksum speed
[ 7.701809] 8regs : 2751 MB/sec
[ 7.704763] 32regs : 3354 MB/sec
[ 7.708021] arm64_neon : 3041 MB/sec
[ 7.708029] xor: using function: 32regs (3354 MB/sec)
[ 7.708046] Key type asymmetric registered
[ 7.708054] Asymmetric key parser 'x509' registered
[ 7.708115] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[ 7.708242] io scheduler mq-deadline registered
[ 7.708258] io scheduler kyber registered
[ 7.709036] rockchip-csi2-dphy-hw fe870000.csi2-dphy-hw: csi2 dphy hw probe successfully!
[ 7.709716] rockchip-csi2-dphy csi2-dphy0: csi2 dphy0 probe successfully!
[ 7.719425] pwm-backlight backlight: supply power not found, using dummy regulator
[ 7.719926] iep: Module initialized.
[ 7.719988] mpp_service mpp-srv:
[ 7.719998] mpp_service mpp-srv: probe start
[ 7.721725] mpp_vdpu2 fdea0400.vdpu: Adding to iommu group 1
[ 7.721924] mpp_vdpu2 fdea0400.vdpu: probe device
[ 7.722493] mpp_vdpu2 fdea0400.vdpu: probing finish
[ 7.722993] mpp_vepu2 fdee0000.vepu: Adding to iommu group 3
[ 7.723183] mpp_vepu2 fdee0000.vepu: probing start
[ 7.723620] mpp_vepu2 fdee0000.vepu: probing finish
[ 7.724183] mpp-iep2 fdef0000.iep: Adding to iommu group 4
[ 7.724364] mpp-iep2 fdef0000.iep: probe device
[ 7.724638] mpp-iep2 fdef0000.iep: allocate roi buffer failed
[ 7.724846] mpp-iep2 fdef0000.iep: probing finish
[ 7.725321] mpp_jpgdec fded0000.jpegd: Adding to iommu group 2
[ 7.725523] mpp_jpgdec fded0000.jpegd: probe device
[ 7.725993] mpp_jpgdec fded0000.jpegd: probing finish
[ 7.727266] mpp_service mpp-srv: probe success
[ 7.732022] dma-pl330 fe530000.dmac: Loaded driver for PL330 DMAC-241330
[ 7.732046] dma-pl330 fe530000.dmac:    DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 7.733948] dma-pl330 fe550000.dmac: Loaded driver for PL330 DMAC-241330
[ 7.733963] dma-pl330 fe550000.dmac:    DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 7.734697] rockchip-pvtm fde00000.pvtm: pvtm@0 probed
[ 7.734827] rockchip-pvtm fde80000.pvtm: pvtm@1 probed
[ 7.734937] rockchip-pvtm fde90000.pvtm: pvtm@2 probed
[ 7.735508] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[ 7.736124] arm-scmi firmware:scmi: Failed. SCMI protocol 22 not active.
[ 7.736415] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[ 7.737219] fe650000.serial: ttyS1 at MMIO 0xfe650000 (irq = 65, base_baud = 1500000) is a 16550A
[ 7.737810] fe670000.serial: ttyS3 at MMIO 0xfe670000 (irq = 66, base_baud = 1500000) is a 16550A
[ 7.738281] fe6a0000.serial: ttyS6 at MMIO 0xfe6a0000 (irq = 67, base_baud = 1500000) is a 16550A
[ 7.738751] fe6b0000.serial: ttyS7 at MMIO 0xfe6b0000 (irq = 68, base_baud = 1500000) is a 16550A
[ 7.739293] fe6d0000.serial: ttyS9 at MMIO 0xfe6d0000 (irq = 69, base_baud = 1500000) is a 16550A
[ 7.742327] rockchip-vop2 fe040000.vop: Adding to iommu group 8
[ 7.748679] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x3f, primary plane phy id: 4
[ 7.748706] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x0, primary plane phy id: -1
[ 7.748717] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x0, primary plane phy id: -1
[ 7.748877] rockchip-vop2 fe040000.vop: [drm:vop2_bind] VP1 plane_mask is zero, so ignore register crtc
[ 7.748891] rockchip-vop2 fe040000.vop: [drm:vop2_bind] VP2 plane_mask is zero, so ignore register crtc
[ 7.748962] [drm] failed to init overlay plane Cluster0-win1
[ 7.749049] rockchip-drm display-subsystem: bound fe040000.vop (ops 0xffffffc0096e8f58)
[ 7.749350] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[ 7.749949] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
[ 7.750199] dwhdmi-rockchip fe0a0000.hdmi: IRQ index 1 not found
[ 7.750592] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops 0xffffffc0096f7ae8)
[ 7.750920] rockchip-drm display-subsystem: route-hdmi: failed to get logo,offset
[ 7.750934] rockchip-drm display-subsystem: can't not find any logo display
[ 7.750946] rockchip-drm display-subsystem: failed to show kernel logo
[ 7.751041] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[ 7.751113] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[ 7.751789] [drm] Initialized rockchip 3.0.0 20140818 for display-subsystem on minor 0
[ 7.758983] input: hdmi_cec_key as /devices/platform/fe0a0000.hdmi/dw-hdmi-cec.1.auto/input/input0
[ 7.760003] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 7.760724] brd: module loaded
[ 7.765989] loop: module loaded
[ 7.766417] zram: Added device: zram0
[ 7.766681] lkdtm: No crash points registered, enable through debugfs
[ 7.769557] ahci fc800000.sata: supply ahci not found, using dummy regulator
[ 7.769718] ahci fc800000.sata: supply phy not found, using dummy regulator
[ 7.769846] ahci fc800000.sata: supply target not found, using dummy regulator
[ 7.769981] ahci fc800000.sata: forcing port_map 0x0 -> 0x1
[ 7.770028] ahci fc800000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 7.770042] ahci fc800000.sata: flags: ncq sntf pm led clo only pmp fbs pio slum part ccc apst
[ 7.770060] ahci fc800000.sata: port 0 is not capable of FBS
[ 7.771110] scsi host0: ahci
[ 7.771406] ata1: SATA max UDMA/133 mmio [mem 0xfc800000-0xfc800fff] port 0x100 irq 19
[ 7.774197] rockchip-spi fe620000.spi: probed, poll=0, rsd=0, cs-inactive=0, ready=0
[ 7.775479] rockchip-spi fe630000.spi: probed, poll=0, rsd=0, cs-inactive=0, ready=0
[ 7.777215] register spi return v = :0
[ 7.778480] CAN device driver interface
[ 7.780404] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found
[ 7.780629] rk_gmac-dwmac fe010000.ethernet: supply phy not found, using dummy regulator
[ 7.780771] rk_gmac-dwmac fe010000.ethernet: clock input or output? (input).
[ 7.780784] rk_gmac-dwmac fe010000.ethernet: TX delay(0x38).
[ 7.780793] rk_gmac-dwmac fe010000.ethernet: RX delay(0x34).
[ 7.780809] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
[ 7.780847] rk_gmac-dwmac fe010000.ethernet: clock input from PHY
[ 7.781109] rk_gmac-dwmac fe010000.ethernet: init for RGMII
[ 7.781373] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 7.781387] rk_gmac-dwmac fe010000.ethernet:    DWMAC4/5
[ 7.781398] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register supported
[ 7.781406] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine supported
[ 7.781412] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported
[ 7.781418] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported
[ 7.781487] rk_gmac-dwmac fe010000.ethernet: TSO supported
[ 7.781496] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 7.781505] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled
[ 7.781513] rk_gmac-dwmac fe010000.ethernet: Using 32 bits DMA width
[ 7.915047] PPP generic driver version 2.4.2
[ 7.915271] PPP BSD Compression module registered
[ 7.915282] PPP Deflate Compression module registered
[ 7.915308] PPP MPPE Compression module registered
[ 7.915322] NET: Registered protocol family 24
[ 7.915523] usbcore: registered new interface driver rtl8150
[ 7.915628] usbcore: registered new interface driver r8152
[ 7.915668] usbcore: registered new interface driver asix
[ 7.915715] usbcore: registered new interface driver ax88179_178a
[ 7.915753] usbcore: registered new interface driver cdc_ether
[ 7.915799] usbcore: registered new interface driver net1080
[ 7.915839] usbcore: registered new interface driver cdc_subset
[ 7.915876] usbcore: registered new interface driver zaurus
[ 7.915926] usbcore: registered new interface driver cdc_ncm
[ 7.915967] usbcore: registered new interface driver qmi_wwan_q
[ 7.926168] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.926217] ehci-pci: EHCI PCI platform driver
[ 7.926319] ehci-platform: EHCI generic platform driver
[ 7.926783] phy phy-fe8b0000.usb2-phy.3: illegal mode
[ 7.928833] ehci-platform fd800000.usb: EHCI Host Controller
[ 7.929065] ehci-platform fd800000.usb: new USB bus registered, assigned bus number 1
[ 7.929196] ehci-platform fd800000.usb: irq 20, io mem 0xfd800000
[ 7.942171] ehci-platform fd800000.usb: USB 2.0 started, EHCI 1.00
[ 7.942344] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 7.942356] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.942365] usb usb1: Product: EHCI Host Controller
[ 7.942371] usb usb1: Manufacturer: Linux 5.10.198 ehci_hcd
[ 7.942378] usb usb1: SerialNumber: fd800000.usb
[ 7.942824] hub 1-0:1.0: USB hub found
[ 7.942861] hub 1-0:1.0: 1 port detected
[ 7.945526] ehci-platform fd880000.usb: EHCI Host Controller
[ 7.945693] ehci-platform fd880000.usb: new USB bus registered, assigned bus number 2
[ 7.945811] ehci-platform fd880000.usb: irq 22, io mem 0xfd880000
[ 7.958876] ehci-platform fd880000.usb: USB 2.0 started, EHCI 1.00
[ 7.959068] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 7.959080] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.959088] usb usb2: Product: EHCI Host Controller
[ 7.959096] usb usb2: Manufacturer: Linux 5.10.198 ehci_hcd
[ 7.959102] usb usb2: SerialNumber: fd880000.usb
[ 7.959528] hub 2-0:1.0: USB hub found
[ 7.959565] hub 2-0:1.0: 1 port detected
[ 7.960247] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 7.960279] ohci-platform: OHCI generic platform driver
[ 7.960607] phy phy-fe8b0000.usb2-phy.3: illegal mode
[ 7.960620] ohci-platform fd840000.usb: Generic Platform OHCI controller
[ 7.960790] ohci-platform fd840000.usb: new USB bus registered, assigned bus number 3
[ 7.960907] ohci-platform fd840000.usb: irq 21, io mem 0xfd840000
[ 8.019648] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[ 8.019660] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.019668] usb usb3: Product: Generic Platform OHCI controller
[ 8.019675] usb usb3: Manufacturer: Linux 5.10.198 ohci_hcd
[ 8.019682] usb usb3: SerialNumber: fd840000.usb
[ 8.020094] hub 3-0:1.0: USB hub found
[ 8.020129] hub 3-0:1.0: 1 port detected
[ 8.020656] ohci-platform fd8c0000.usb: Generic Platform OHCI controller
[ 8.020814] ohci-platform fd8c0000.usb: new USB bus registered, assigned bus number 4
[ 8.020922] ohci-platform fd8c0000.usb: irq 23, io mem 0xfd8c0000
[ 8.079660] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[ 8.079673] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.079681] usb usb4: Product: Generic Platform OHCI controller
[ 8.079688] usb usb4: Manufacturer: Linux 5.10.198 ohci_hcd
[ 8.079695] usb usb4: SerialNumber: fd8c0000.usb
[ 8.080105] hub 4-0:1.0: USB hub found
[ 8.080140] hub 4-0:1.0: 1 port detected
[ 8.081417] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 8.081635] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 5
[ 8.081772] xhci-hcd xhci-hcd.4.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000800002010010
[ 8.081836] xhci-hcd xhci-hcd.4.auto: irq 83, io mem 0xfd000000
[ 8.081967] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 8.082126] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 6
[ 8.082174] xhci-hcd xhci-hcd.4.auto: Host supports USB 3.0 SuperSpeed
[ 8.082314] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 8.082326] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.082333] usb usb5: Product: xHCI Host Controller
[ 8.082340] usb usb5: Manufacturer: Linux 5.10.198 xhci-hcd
[ 8.082347] usb usb5: SerialNumber: xhci-hcd.4.auto
[ 8.082765] hub 5-0:1.0: USB hub found
[ 8.082802] hub 5-0:1.0: 1 port detected
[ 8.083152] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 8.083245] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 8.083256] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.083264] usb usb6: Product: xHCI Host Controller
[ 8.083271] usb usb6: Manufacturer: Linux 5.10.198 xhci-hcd
[ 8.083278] usb usb6: SerialNumber: xhci-hcd.4.auto
[ 8.083661] hub 6-0:1.0: USB hub found
[ 8.083694] hub 6-0:1.0: 1 port detected
[ 8.084138] usbcore: registered new interface driver cdc_acm
[ 8.084149] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 8.084216] usbcore: registered new interface driver usblp
[ 8.084265] usbcore: registered new interface driver cdc_wdm
[ 8.084540] usbcore: registered new interface driver uas
[ 8.084625] usbcore: registered new interface driver usb-storage
[ 8.084719] usbcore: registered new interface driver usbserial_generic
[ 8.084745] usbserial: USB Serial support registered for generic
[ 8.084790] usbcore: registered new interface driver ch341
[ 8.084811] usbserial: USB Serial support registered for ch341-uart
[ 8.084855] usbcore: registered new interface driver cp210x
[ 8.084876] usbserial: USB Serial support registered for cp210x
[ 8.084941] usbcore: registered new interface driver ftdi_sio
[ 8.084963] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 8.085087] usbcore: registered new interface driver keyspan
[ 8.085112] usbserial: USB Serial support registered for Keyspan - (without firmware)
[ 8.085134] usbserial: USB Serial support registered for Keyspan 1 port adapter
[ 8.085155] usbserial: USB Serial support registered for Keyspan 2 port adapter
[ 8.085176] usbserial: USB Serial support registered for Keyspan 4 port adapter
[ 8.085205] ata1: SATA link down (SStatus 0 SControl 300)
[ 8.085225] usbcore: registered new interface driver option
[ 8.085249] usbserial: USB Serial support registered for GSM modem (1-port)
[ 8.085402] usbcore: registered new interface driver oti6858
[ 8.085424] usbserial: USB Serial support registered for oti6858
[ 8.085473] usbcore: registered new interface driver pl2303
[ 8.085540] usbserial: USB Serial support registered for pl2303
[ 8.085594] usbcore: registered new interface driver qcserial
[ 8.085617] usbserial: USB Serial support registered for Qualcomm USB modem
[ 8.085679] usbcore: registered new interface driver sierra
[ 8.085703] usbserial: USB Serial support registered for Sierra USB modem
[ 8.087146] usbcore: registered new interface driver xpad
[ 8.087227] <<-GTP-INFO->> GTP driver installing...
[ 8.087516] usbcore: registered new interface driver usbtouchscreen
[ 8.088071] i2c /dev entries driver
[ 8.091253] rk808 0-0020: chip id: 0x8090
[ 8.091311] rk808 0-0020: No cache defaults, reading back from HW
[ 8.115018] rk808 0-0020: source: on=0x40, off=0x00
[ 8.115036] rk808 0-0020: support dcdc3 fb mode:-22, 1
[ 8.115047] rk808 0-0020: support pmic reset mode:0,0
[ 8.120530] rk808-regulator rk808-regulator: there is no dvs0 gpio
[ 8.120566] rk808-regulator rk808-regulator: there is no dvs1 gpio
[ 8.120991] vdd_logic: supplied by vcc3v3_sys
[ 8.121999] vdd_gpu: supplied by vcc3v3_sys
[ 8.122592] vcc_ddr: supplied by vcc3v3_sys
[ 8.123178] vdd_npu: supplied by vcc3v3_sys
[ 8.124105] vcc_1v8: supplied by vcc3v3_sys
[ 8.124680] vdda0v9_image: supplied by vcc3v3_sys
[ 8.126117] vdda_0v9: supplied by vcc3v3_sys
[ 8.127197] vdda0v9_pmu: supplied by vcc3v3_sys
[ 8.128295] vccio_acodec: supplied by vcc3v3_sys
[ 8.129736] vccio_sd: supplied by vcc3v3_sys
[ 8.130817] vcc3v3_pmu: supplied by vcc3v3_sys
[ 8.132252] vcca_1v8: supplied by vcc3v3_sys
[ 8.133351] vcca1v8_pmu: supplied by vcc3v3_sys
[ 8.134430] vcca1v8_image: supplied by vcc3v3_sys
[ 8.135902] vcc_3v3: supplied by vcc3v3_sys
[ 8.136805] vcc3v3_sd: supplied by vcc3v3_sys
[ 8.137381] rk817-charger: Failed to locate of_node [id: -1]
[ 8.137554] rk817-charger rk817-charger: Failed to find matching dt id
[ 8.140735] input: rk805 pwrkey as /devices/platform/fdd40000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input1
[ 8.142977] fan53555 test 0x1c succes
[ 8.143916] fan53555-regulator 0-001c: FAN53555 Option[12] Rev[15] Detected!
[ 8.145883] vdd_cpu: supplied by vcc5v0_sys
[ 8.352183] rk3x-i2c fe5d0000.i2c: timeout, ipd: 0x11, state: 2
[ 8.352216] rtc-hym8563 4-0051: could not init device, -110
[ 8.352239] rtc-hym8563: probe of 4-0051 failed with error -110
[ 8.435990] ov5645 1-003c: OV5645 detected at address 0x3c
[ 8.436025] [ov5645_probe, 1742]: zhangpeng enter
[ 8.437289] rkcifhw fdfe0000.rkcif: Adding to iommu group 7
[ 8.437791] rkcifhw fdfe0000.rkcif: can't request region for resource [mem 0xfdfe0000-0xfdfe7fff]
[ 8.437878] rkcifhw fdfe0000.rkcif: No reserved memory region assign to CIF
[ 8.438065] rkcif rkcif_mipi_lvds: rkcif driver version: v00.02.00
[ 8.438197] rkcif rkcif_mipi_lvds: attach to cif hw node
[ 8.438208] rkcif rkcif_mipi_lvds: rkcif wait line 0
[ 8.438219] : terminal subdev does not exist
[ 8.438227] : terminal subdev does not exist
[ 8.438233] : terminal subdev does not exist
[ 8.438239] : terminal subdev does not exist
[ 8.439686] rkcif rkcif_mipi_lvds: No memory-region-thunderboot specified
[ 8.440822] rockchip-mipi-csi2-hw fdfb0000.mipi-csi2-hw: enter mipi csi2 hw probe!
[ 8.440991] rockchip-mipi-csi2-hw fdfb0000.mipi-csi2-hw: probe success, v4l2_dev:mipi-csi2-hw!
[ 8.441393] rockchip-mipi-csi2 mipi-csi2: attach to csi2 hw node
[ 8.441508] rkcif rkcif_mipi_lvds: Entity type for entity rockchip-mipi-csi2 was not initialized!
[ 8.441524] rockchip-mipi-csi2: Async registered subdev
[ 8.441548] rockchip-csi2-dphy csi2-dphy0: dphy0 matches m00_b_ov5645 1-003c:bus type 5
[ 8.442012] rkcif_mipi_lvds: Async subdev notifier completed
[ 8.442023] rockchip-mipi-csi2: probe success, v4l2_dev:rkcif_mipi_lvds!
[ 8.443936] usbcore: registered new interface driver uvcvideo
[ 8.443950] USB Video Class driver (1.1.1)
[ 8.445825] device-mapper: ioctl: 4.44.0-ioctl (2021-02-01) initialised: dm-devel@redhat.com
[ 8.446251] Bluetooth: HCI UART driver ver 2.3
[ 8.446266] Bluetooth: HCI UART protocol H4 registered
[ 8.446273] Bluetooth: HCI UART protocol ATH3K registered
[ 8.446353] usbcore: registered new interface driver bfusb
[ 8.446406] usbcore: registered new interface driver btusb
[ 8.447456] cpu cpu0: bin=0
[ 8.447522] cpu cpu0: leakage=29
[ 8.447564] cpu cpu0: pvtm = 87430, from nvmem
[ 8.447580] cpu cpu0: pvtm-volt-sel=2
[ 8.447643] cpu cpu0: soc version=0, speed=2
[ 8.449359] cpu cpu0: avs=0
[ 8.449631] cpu cpu0: EM: created perf domain
[ 8.449693] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 8.455814] sdhci: Secure Digital Host Controller Interface driver
[ 8.455838] sdhci: Copyright(c) Pierre Ossman
[ 8.455846] Synopsys Designware Multimedia Card Interface Driver
[ 8.456841] sdhci-pltfm: SDHCI platform and OF driver helper
[ 8.457372] dwmmc_rockchip fe000000.dwmmc: No normal pinctrl state
[ 8.457394] dwmmc_rockchip fe000000.dwmmc: No idle pinctrl state
[ 8.457524] dwmmc_rockchip fe000000.dwmmc: IDMAC supports 32-bit address mode.
[ 8.457540] dwmmc_rockchip fe2b0000.dwmmc: No normal pinctrl state
[ 8.457552] dwmmc_rockchip fe2b0000.dwmmc: No idle pinctrl state
[ 8.457558] dwmmc_rockchip fe000000.dwmmc: Using internal DMA controller.
[ 8.457568] dwmmc_rockchip fe000000.dwmmc: Version ID is 270a
[ 8.457628] dwmmc_rockchip fe000000.dwmmc: DW MMC controller at irq 49,32 bit host data width,256 deep fifo
[ 8.457658] dwmmc_rockchip fe2b0000.dwmmc: IDMAC supports 32-bit address mode.
[ 8.457681] dwmmc_rockchip fe2b0000.dwmmc: Using internal DMA controller.
[ 8.457694] dwmmc_rockchip fe2b0000.dwmmc: Version ID is 270a
[ 8.457730] dwmmc_rockchip fe2b0000.dwmmc: DW MMC controller at irq 50,32 bit host data width,256 deep fifo
[ 8.458035] dwmmc_rockchip fe000000.dwmmc: allocated mmc-pwrseq
[ 8.458051] mmc_host mmc3: card is non-removable.
[ 8.458679] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
[ 8.458782] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
mount: /oem: can't find PARTLABEL=oem.
[ 8.459729] cryptodev: driver 1.12 loaded.
mount: /userdata: wrong fs type, bad option, bad superblock on /dev/mmcblk0p14, missing codepage or helper program, or other error.
[ 8.459811] hid: raw HID events driver (C) Jiri Kosina
dmesg(1) may have more information after failed mount system call.
[ 8.460198] usbcore: registered new interface driver usbhid
[ 8.460210] usbhid: USB HID core driver
[ 8.461318] rockchip,bus bus-npu: bin=0
[ 8.461337] rockchip,bus bus-npu: Failed to get leakage
[ 8.461391] rockchip,bus bus-npu: pvtm = 87430, from nvmem
[ 8.461406] rockchip,bus bus-npu: pvtm-volt-sel=1
[ 8.461626] rockchip,bus bus-npu: avs=0
[ 8.465854] rp_power prepare build 9 gpio
[ 8.466015] rp_power request pwr_5v_3v3
[ 8.466042] success request gpio75 out
[ 8.466059] rp_power request led
[ 8.466073] success request gpio114 flash
[ 8.466087] rp_power request usb_pwr
[ 8.466100] success request gpio6 out
[ 8.466116] rp_power request otg_pwr
[ 8.466127] success request gpio5 out
[ 8.466141] rp_power request usb_rst
[ 8.466152] success request gpio8 out
[ 8.466176] rp_power: probe of rp_power failed with error -1
[ 8.466435] rp_gpio prepare build 9 gpio
[ 8.466554] rp_gpio request gpio1d0
[ 8.466570] success request gpio56 out
[ 8.466587] rp_gpio request gpio1d1
[ 8.466598] success request gpio57 out
[ 8.466613] rp_gpio request gpio1d2
[ 8.466624] success request gpio58 out
[ 8.466637] rp_gpio request gpio1d3
[ 8.466649] success request gpio59 out
[ 8.466662] rp_gpio request gpio1d4
[ 8.466673] success request gpio60 out
[ 8.466732] rp_gpio request gpio4a0
[ 8.466746] success request gpio128 out
[ 8.466762] rp_gpio request gpio4a1
Start mounting all internal partitions in /etc/fstab
[ 8.466772] success request gpio129 out
Log saved to /var/log/mount-all.log
[ 8.466787] rp_gpio request gpio1a4
Note: Will skip fsck, remove /.skip_fsck to enable
[ 8.466798] success request gpio36 out
[ 8.466815] rp_gpio request gpio3c1
[ 8.466827] success request gpio113 out
[ 8.467240] mhi_init Quectel_Linux_PCIE_MHI_Driver_V1.3.1
[ 8.467452] sprd_pci_ep_dev_init Quectel_Linux&Android_SPRD_PCIE_Driver_V1.1.8
[ 8.467982] sipc: name=sprd,sipc
[ 8.467989] sipc: type=1
[ 8.467993] sipc: dst =1
[ 8.467997] sipc: ep_dev=0
[2]: Handling /dev/mmcblk0p14 /userdata ext4 defaults 2
[ 8.468001] sipc: smem_type = 0
[0]: Handling /dev/mmcblk1p6 / ext4 rw,noauto 1
[ 8.468502] sipc: smem_base=0x5400000, dst_smem_base=0x5400000, smem_size=0x300000
[ 8.468507] sipc: high_offset=0x0n
[ 8.468510] smsg_ipc_create: sprd,sipc
[ 8.468869] smem_init: pool addr = 0x5400000, size = 0x300000 added.
[ 8.468884] smsg_ipc_smem_init: ring_base = 0x5400000, ring_size = 0x1000
[ 8.469156] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[2]: Mounting /dev/mmcblk0p14(ext4) on /userdata with -o defaults
[ 8.469688] spipe_probe!
mount: /userdata: wrong fs type, bad option, bad superblock on /dev/mmcblk0p14, missing codepage or helper program, or other error.
[ 8.469697] spipe: after parse device tree, name=spipe_nr, dst=1, channel=4, ringnr=15, rxbuf_size=0x1000, txbuf_size=0x1000
dmesg(1) may have more information after failed mount system call.
[ 8.469708] sbuf_host_init: channel 1-4, offset = 0x0!
[0]: Resizing /dev/mmcblk1p6(ext4)
[ 8.470103] smsg_ch_open: channel 1-4 send open msg!
resize2fs 1.46.5 (30-Dec-2021)
[ 8.471355] spipe_probe!
[ 8.471365] spipe: after parse device tree, name=sdiag_nr, dst=1, channel=21, ringnr=1, rxbuf_size=0x8000, txbuf_size=0x40000
[ 8.471375] sbuf_host_init: channel 1-21, offset = 0x0!
[ 8.471608] smsg_ch_open: channel 1-21 send open msg!
[ 8.471667] spipe_probe!
[ 8.471675] spipe: after parse device tree, name=stty_nr, dst=1, channel=6, ringnr=32, rxbuf_size=0x800, txbuf_size=0x800
[ 8.471683] sbuf_host_init: channel 1-6, offset = 0x0!
[ 8.471963] smsg_ch_open: channel 1-6 send open msg!
[ 8.473993] spipe_probe!
[ 8.474008] spipe: after parse device tree, name=snv_nr, dst=1, channel=40, ringnr=1, rxbuf_size=0x1000, txbuf_size=0x40400
[ 8.474023] sbuf_host_init: channel 1-40, offset = 0x0!
[ 8.474271] smsg_ch_open: channel 1-40 send open msg!
[ 8.474816] spool: name=slog_nr, dst=1, channel=5, pre_cfg=0
[ 8.474826] spool: tx_num=0, tx_size=0, rx_num=32, rx_size=65536
[ 8.475144] smsg_ch_open: channel 1-5 send open msg!
[ 8.475728] usbcore: registered new interface driver snd-usb-audio
[ 8.477854] rk817-codec rk817-codec: DMA mask not set
[ 8.483002] rk-multicodecs rk809-sound: Failed to get ADC channel
[ 8.483137] rk-multicodecs rk809-sound: ASoC: Property 'rockchip,audio-routing' does not exist or its length is not even
[ 8.484271] rk817-codec rk817-codec: rk817_probe: chip_name:0x80, chip_ver:0x95
[ 8.488201] mmc0: SDHCI controller on fe310000.sdhci [fe310000.sdhci] using ADMA
[ 8.488655] rk-multicodecs rk809-sound: Don't need to map headset detect gpio to irq
[ 8.491248] IPVS: Registered protocols (TCP, UDP)
[ 8.491299] IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
[ 8.491410] IPVS: ipvs loaded.
[ 8.491420] IPVS: [rr] scheduler registered.
[ 8.491650] Initializing XFRM netlink socket
[ 8.491965] NET: Registered protocol family 10
[ 8.492622] Segment Routing with IPv6
[ 8.492690] NET: Registered protocol family 17
[ 8.492710] NET: Registered protocol family 15
[ 8.492764] Bridge firewalling registered
[ 8.492771] can: controller area network core
[ 8.492804] NET: Registered protocol family 29
[ 8.492810] can: raw protocol
[ 8.492818] can: broadcast manager protocol
[ 8.492828] can: netlink gateway - max_hops=1
[ 8.493007] Bluetooth: RFCOMM socket layer initialized
[ 8.493039] Bluetooth: RFCOMM ver 1.11
[ 8.493080] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 8.493090] Bluetooth: HIDP socket layer initialized
[ 8.493419] NET: Registered protocol family 41
[ 8.493591] 8021q: 802.1Q VLAN Support v1.8
[ 8.493625] [BT_RFKILL]: Enter rfkill_rk_init
[ 8.493631] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 8.494540] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[ 8.494590] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6398s
[ 8.494596] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ 8.494602] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[ 8.494632] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 124, flags = 0.
[ 8.494641] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[ 8.494647] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ 8.494654] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1
[ 8.494660] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[ 8.495703] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 142.
[ 8.495734] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 133.
[ 8.495745] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 134.
[ 8.495755] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 137.
[ 8.495816] [BT_RFKILL]: Request irq for bt wakeup host
[ 8.495901] [BT_RFKILL]: ** disable irq
[ 8.496064] [BT_RFKILL]: bt_default device registered.
[ 8.496200] Key type dns_resolver registered
[ 8.497971] Loading compiled-in X.509 certificates
[ 8.500381] Btrfs loaded, crc32c=crc32c-generic
[ 8.500637] pstore: Using crash dump compression: deflate
[ 8.501564] rga: rga2, irq = 31, match scheduler
[ 8.502001] rga: rga2 hardware loaded successfully, hw_version:3.2.63318.
[ 8.502028] rga: rga2 probe successfully
[ 8.502328] rga_iommu: IOMMU binding successfully, default mapping core[0x4]
[ 8.502584] rga: Module initialized. v1.3.1
[ 8.531712] mmc0: Host Software Queue enabled
[ 8.531747] mmc0: new HS200 MMC card at address 0001
[ 8.532439] mmc_host mmc1: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
[ 8.532442] mmcblk0: mmc0:0001 ARJ11X 29.1 GiB
[ 8.532730] mmcblk0boot0: mmc0:0001 ARJ11X partition 1 4.00 MiB
[ 8.533047] mmcblk0boot1: mmc0:0001 ARJ11X partition 2 4.00 MiB
[ 8.533241] mmcblk0rpmb: mmc0:0001 ARJ11X partition 3 4.00 MiB, chardev (236:0)
[ 8.533619] dwmmc_rockchip fe2b0000.dwmmc: All phases bad!
[ 8.533654] mmc1: tuning execution failed: -5
[ 8.533687] mmc1: error -5 whilst initialising SD card
[ 8.536225] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14
[ 8.545572] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 375000Hz, actual 375000HZ div = 0)
[ 8.607176] vendor storage:20190527 ret = 0
[ 8.607203] mmc_host mmc1: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
[ 8.608113] dwmmc_rockchip fe2b0000.dwmmc: All phases bad!
[ 8.608125] mmc1: tuning execution failed: -5
[ 8.623774] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 375000Hz, actual 375000HZ div = 0)
[ 8.667757] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 8.668085] mmc1: new high speed SDHC card at address 0001
[ 8.670249] mmcblk1: mmc1:0001 SD16G 29.1 GiB
[ 8.675935] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 8.678408] mmcblk1: p1 p2 p3 p4 p5 p6
[ 8.690037] mpp_rkvenc fdf40000.rkvenc: Adding to iommu group 5
[ 8.690352] mpp_rkvenc fdf40000.rkvenc: probing start
[ 8.691188] mpp_rkvenc fdf40000.rkvenc: bin=0
[ 8.691230] mpp_rkvenc fdf40000.rkvenc: Failed to get leakage
[ 8.691298] mpp_rkvenc fdf40000.rkvenc: pvtm = 87430, from nvmem
[ 8.691320] mpp_rkvenc fdf40000.rkvenc: pvtm-volt-sel=1
[ 8.691655] mpp_rkvenc fdf40000.rkvenc: avs=0
[ 8.691909] mpp_rkvenc fdf40000.rkvenc: failed to find power_model node
[ 8.691927] mpp_rkvenc fdf40000.rkvenc: failed to initialize power model
[ 8.691940] mpp_rkvenc fdf40000.rkvenc: failed to get dynamic-coefficient
Filesystem at /dev/mmcblk1p6 is mounted on /; on-line resizing required
[ 8.692909] mpp_rkvenc fdf40000.rkvenc: probing finish
old_desc_blocks = 1, new_desc_blocks = 2
[ 8.693561] mpp_rkvdec2 fdf80200.rkvdec: Adding to iommu group 6
The filesystem on /dev/mmcblk1p6 is now 7571963 (4k) blocks long.
[ 8.693913] mpp_rkvdec2 fdf80200.rkvdec: rkvdec, probing start

[ 8.694446] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_a is not found!
[ 8.694464] rkvdec2_init:1022: No niu aclk reset resource define
[ 8.694480] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_h is not found!
[ 8.694490] rkvdec2_init:1025: No niu hclk reset resource define
[ 8.694810] mpp_rkvdec2 fdf80200.rkvdec: bin=0
[ 8.694955] mpp_rkvdec2 fdf80200.rkvdec: leakage=54
/etc/init.d/S01boot-complete.sh: line 17: /proc/rp_system_flag/rp_boot_completed: No such file or directory
[ 8.694978] mpp_rkvdec2 fdf80200.rkvdec: leakage-volt-sel=0
Starting syslogd: [ 8.695029] mpp_rkvdec2 fdf80200.rkvdec: pvtm = 87430, from nvmem
OK
[ 8.695049] mpp_rkvdec2 fdf80200.rkvdec: pvtm-volt-sel=1
[ 8.695315] mpp_rkvdec2 fdf80200.rkvdec: avs=0
[ 8.695560] mpp_rkvdec2 fdf80200.rkvdec: failed to find power_model node
Starting klogd: OK
[ 8.695579] mpp_rkvdec2 fdf80200.rkvdec: failed to initialize power model
[ 8.695592] mpp_rkvdec2 fdf80200.rkvdec: failed to get dynamic-coefficient
Running sysctl: [ 8.695778] mpp_rkvdec2 fdf80200.rkvdec: sram_start 0x00000000fdcc0000
OK
[ 8.695794] mpp_rkvdec2 fdf80200.rkvdec: rcb_iova 0x0000000010000000
[ 8.695805] mpp_rkvdec2 fdf80200.rkvdec: sram_size 45056
[ 8.695816] mpp_rkvdec2 fdf80200.rkvdec: rcb_size 65536
Populating /dev using udev: [ 8.695829] mpp_rkvdec2 fdf80200.rkvdec: min_width 512
[ 8.695912] mpp_rkvdec2 fdf80200.rkvdec: link mode probe finish
[ 8.696019] mpp_rkvdec2 fdf80200.rkvdec: probing finish
[ 8.697372] rockchip-iodomain fdc20000.syscon:io-domains: pmuio2(3300000 uV) supplied by vcc3v3_pmu
[ 8.697584] mali fde60000.gpu: Kernel DDK version g18p0-01eac0
[ 8.697615] rockchip-iodomain fdc20000.syscon:io-domains: vccio1(3000000 uV) supplied by vccio_acodec
[ 8.697823] rockchip-iodomain fdc20000.syscon:io-domains: vccio3(3300000 uV) supplied by vccio_sd
[ 8.698036] rockchip-iodomain fdc20000.syscon:io-domains: vccio4(3300000 uV) supplied by vcc_3v3
[ 8.698199] rockchip-iodomain fdc20000.syscon:io-domains: vccio5(3300000 uV) supplied by vcc_3v3
[ 8.698237] mali fde60000.gpu: bin=0
[ 8.698310] mali fde60000.gpu: leakage=8
[ 8.698363] mali fde60000.gpu: pvtm = 87430, from nvmem
[ 8.698391] mali fde60000.gpu: pvtm-volt-sel=2
[ 8.698406] rockchip-iodomain fdc20000.syscon:io-domains: vccio6(1800000 uV) supplied by vcc_1v8
[ 8.698417] mali fde60000.gpu: soc version=0, speed=2
[ 8.698541] rockchip-iodomain fdc20000.syscon:io-domains: vccio7(3300000 uV) supplied by vcc_3v3
[ 8.699439] mali fde60000.gpu: avs=0
[ 8.699485] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 143; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[ 8.699552] input: adc-keys as /devices/platform/adc-keys/input/input2
[ 8.700220] mali fde60000.gpu: GPU identified as 0x2 arch 7.4.0 r1p0 status 0
[ 8.700350] mali fde60000.gpu: No priority control manager is configured
[ 8.700848] mali fde60000.gpu: No memory group manager is configured
[ 8.703460] mali fde60000.gpu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 8.705040] mali fde60000.gpu: Probed as mali0
[ 8.715833] rk808-rtc rk808-rtc: registered as rtc0
[ 8.717857] rk808-rtc rk808-rtc: setting system clock to 2017-08-04T09:00:09 UTC (1501837209)
[ 8.717928] rkcif rkcif_mipi_lvds: clear unready subdev num: 0
[ 8.719064] rockchip_headset rk-headset: Can not read property hook_gpio
[ 8.719089] rockchip_headset rk-headset: have not set adc chan
[ 8.719096] rockchip_headset rk-headset: headset have no hook mode
[ 8.719275] input: rk-headset as /devices/platform/rk-headset/input/input3
[ 8.720065] RKNPU fde40000.npu: Adding to iommu group 0
[ 8.720474] RKNPU fde40000.npu: RKNPU: rknpu iommu is enabled, using iommu mode
[ 8.720702] RKNPU fde40000.npu: can't request region for resource [mem 0xfde40000-0xfde4ffff]
[ 8.721300] [drm] Initialized rknpu 0.9.3 20231121 for fde40000.npu on minor 1
[ 8.724248] RKNPU fde40000.npu: bin=0
[ 8.724313] RKNPU fde40000.npu: leakage=4
[ 8.724351] RKNPU fde40000.npu: pvtm = 87430, from nvmem
[ 8.724368] RKNPU fde40000.npu: pvtm-volt-sel=2
[ 8.724383] RKNPU fde40000.npu: soc version=0, speed=2
[ 8.724929] RKNPU fde40000.npu: avs=0
[ 8.725130] RKNPU fde40000.npu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 8.725722] RKNPU fde40000.npu: failed to find power_model node
[ 8.725734] RKNPU fde40000.npu: RKNPU: failed to initialize power model
[ 8.725741] RKNPU fde40000.npu: RKNPU: failed to get dynamic-coefficient
[ 8.727207] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 8.729046] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 8.730035] rockchip-pm rockchip-suspend: not set pwm-regulator-config
[ 8.730592] rockchip-suspend not set sleep-mode-config for mem-lite
[ 8.730601] rockchip-suspend not set wakeup-config for mem-lite
[ 8.730609] rockchip-suspend not set sleep-mode-config for mem-ultra
[ 8.730614] rockchip-suspend not set wakeup-config for mem-ultra
[ 8.731613] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 406; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '09:41:21', on 'Jul 8 2025'.
[ 8.731997] Mali:
[ 8.732000] Mali device driver loaded
[ 8.732388] ALSA device list:
[ 8.732401] #0: rockchip-rk809
[ 8.732407] #1: rockchip,hdmi
[ 8.733061] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 8.733080] cfg80211: failed to load regulatory.db
[ 8.746523] EXT4-fs (mmcblk1p6): mounted filesystem with ordered data mode. Opts: (null)
[ 8.746609] VFS: Mounted root (ext4 filesystem) on device 179:102.
[ 8.747691] devtmpfs: mounted
[ 8.756292] Freeing unused kernel memory: 7552K
[ 8.795775] Run /sbin/init as init process
[ 8.928900] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 375000Hz, actual 375000HZ div = 0)
[ 9.041718] EXT4-fs (mmcblk1p6): re-mounted. Opts: (null)
[ 9.222191] ---headsetobserve_work---
[ 9.332244] old_status == headset_info->headset_status
[ 9.629913] EXT4-fs (mmcblk0p14): VFS: Can't find ext4 filesystem
[ 9.899479] EXT4-fs (mmcblk0p14): VFS: Can't find ext4 filesystem
[ 9.949638] EXT4-fs (mmcblk1p6): resizing filesystem from 249344 to 7571963 blocks
[ 10.356684] EXT4-fs (mmcblk1p6): resized filesystem to 7571963
[ 10.734238] udevd[324]: starting version 3.2.10
[ 10.797754] udevd[328]: starting eudev-3.2.10
[ 11.096932] stream_cif_mipi_id0: open video, entity use_countt 1
[ 11.096999] stream_cif_mipi_id1: open video, entity use_countt 1
[ 11.097127] stream_cif_mipi_id0: close video, entity use_count 0
[ 11.097157] stream_cif_mipi_id1: close video, entity use_count 0
[ 11.105172] stream_cif_mipi_id2: open video, entity use_countt 1
[ 11.105779] stream_cif_mipi_id2: close video, entity use_count 0
[ 11.123256] stream_cif_mipi_id3: open video, entity use_countt 1
[ 11.123489] stream_cif_mipi_id3: close video, entity use_count 0
done
Starting irqbalance: OK
Saving random seed: OK
Starting system message bus: done
Starting iptables: OK
Starting bluetoothd: OK
Starting network: Failed to detect Wi-Fi/BT chip!
ln: failed to create symbolic link '': No such file or directory
OK
Starting dhcpcd...
dhcpcd-9.4.1 starting
dev: loaded udev
no interfaces have a carrier
forked to background, child pid 533
Starting ntpd: [ 12.335641] rk_gmac-dwmac fe010000.ethernet eth0: PHY [stmmac-1:00] driver [RTL8211F Gigabit Ethernet] (irq=POLL)
[ 12.338188] dwmac4: Master AXI performs any burst length
[ 12.338230] rk_gmac-dwmac fe010000.ethernet eth0: No Safety Features support found
[ 12.338261] rk_gmac-dwmac fe010000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 12.338586] rk_gmac-dwmac fe010000.ethernet eth0: registered PTP clock
[ 12.339078] rk_gmac-dwmac fe010000.ethernet eth0: configuring for phy/rgmii link mode
OK
starting weston... done.
Starting dropbear sshd: OK
Starting pulseaudio: OK
Starting dnsmasq: OK
/bin/list-iodomain.sh version: V1.0.1
Get CHIP ID: rk356x
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXX PLEASE CHECK IO-DOMAIN !!!!!!!!!!!!!!!
XXXXXXXXXX 请务必检查IO电源域配置 !!!!!!!!!!!!!!!
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Get IO DOMAIN VALUE:
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
注意事项：PMUIO1/PMUIO2 固定不可配
VCCIO2电平由硬件FLASH_VOL_SEL决定:
当VCCIo2供电是1.8V,则FLASH_VOL_SEL管脚必须保持为高电平;
当VCCIO2供电是3.3V,则FLASH_VOL_SEL管脚必须保持为低电平;
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
pmuio2_vsel: 3.3V
vccio7_vsel: 3.3V
vccio6_vsel: 1.8V
vccio5_vsel: 3.3V
vccio4_vsel: 3.3V
vccio3_vsel: 3.3V
vccio2_vsel: 3.3V
vccio1_vsel: 3.3V
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
The camera soft link is automatically createdOK
W: [pulseaudio] main.c: This program is not intended to be run as root (unless --system is specified).
W: [pulseaudio] main.c: Compiled with DEPRECATED libsamplerate support!
[ 14.031853] file system registered
[ 14.258982] read descriptors
[ 14.259037] read strings
[ 14.484803] dwhdmi-rockchip fe0a0000.hdmi: Rate 0 missing; compute N dynamically
[ 14.485727] dwhdmi-rockchip fe0a0000.hdmi: Rate 0 missing; compute N dynamically
alsa-lib main.c:1541:(snd_use_case_mgr_open) error: failed to import hw:1 use case configuration -2
-i use default asound.conf
Starting mobilenet:[ 14.641965] dwhdmi-rockchip fe0a0000.hdmi: Rate 0 missing; compute N dynamically
OK
[ 14.642489] dwhdmi-rockchip fe0a0000.hdmi: Rate 0 missing; compute N dynamically
Starting input-event-daemon: done
root@rk3566-buildroot:/# W: [pulseaudio] authkey.c: Failed to open cookie file '/userdata/.pulse/.config/pulse/cookie': No such file or directory
W: [pulseaudio] authkey.c: Failed to load authentication key '/userdata/.pulse/.config/pulse/cookie': No such file or directory
W: [pulseaudio] authkey.c: Failed to open cookie file '/userdata/.pulse/.pulse-cookie': No such file or directory
W: [pulseaudio] authkey.c: Failed to load authentication key '/userdata/.pulse/.pulse-cookie': No such file or directory
E: [pulseaudio] module-rescue-streams.c: module-rescue-stream is obsolete and should no longer be loaded. Please remove it from your configuration.
Date: 2017-08-04 CST
[17:00:15.680] weston 13.0.0
https://wayland.freedesktop.org
Bug reports to: https://gitlab.freedesktop.org/wayland/weston/issues/
Build: linux5.10-rkr7.1(v1.4.0_20231220)-395-gad3330a33b+
[17:00:15.684] Command line: /usr/bin/weston
[17:00:15.684] OS: Linux, 5.10.198, #1 SMP Tue Jul 8 09:38:35 CST 2025, aarch64
[17:00:15.684] Flight recorder: enabled
[17:00:15.684] warning: XDG_RUNTIME_DIR "/var/run" is not configured
correctly. Unix access mode must be 0700 (current mode is 0755),
and must be owned by the user UID 0 (current owner is UID 0).
Refer to your distribution on how to get it, or
http://www.freedesktop.org/wiki/Specifications/basedir-spec
on how to implement it.
/etc/xdg/weston/weston.ini.d/02-desktop.ini: "shell/locking" from "false" to "true"
[17:00:15.780] Using config file '/etc/xdg/weston/weston.ini'
[17:00:15.782] Output repaint window is -1 ms maximum.
[17:00:15.786] Loading module '/usr/lib/libweston-13/drm-backend.so'
E: [pulseaudio] module-console-kit.c: GetSessionsForUnixUser() call failed: org.freedesktop.DBus.Error.ServiceUnknown: The name org.freedesktop.ConsoleKit was not provided by any .service files
E: [pulseaudio] module.c: Failed to load module "module-console-kit" (argument: ""): initialization failed.
[17:00:15.798] initializing drm backend
[17:00:15.798] Entering mirror mode.
[17:00:15.798] Trying direct launcher...
[17:00:15.804] using /dev/dri/card0
[17:00:15.804] DRM: does not support atomic modesetting
[17:00:15.804] DRM: does not support GBM modifiers
[17:00:15.804] DRM: does not support async page flipping
[17:00:15.804] DRM: supports picture aspect ratio
W: [pulseaudio] server-lookup.c: Unable to contact D-Bus: org.freedesktop.DBus.Error.NotSupported: Using X11 for dbus-daemon autolaunch was disabled at compile time, set your DBUS_SESSION_BUS_ADDRESS instead
W: [pulseaudio] main.c: Unable to contact D-Bus: org.freedesktop.DBus.Error.NotSupported: Using X11 for dbus-daemon autolaunch was disabled at compile time, set your DBUS_SESSION_BUS_ADDRESS instead
[17:00:15.815] Loading module '/usr/lib/libweston-13/gl-renderer.so'
arm_release_ver: g13p0-01eac0, rk_so_ver: 10
[17:00:15.994] EGL version: 1.4 Bifrost-"g13p0-01eac0"
[17:00:15.994] EGL vendor: ARM
[17:00:15.994] EGL client APIs: OpenGL_ES
[17:00:15.994] EGL features:
EGL Wayland extension: yes
context priority: yes
buffer age: no
partial update: yes
swap buffers with damage: no
configless context: yes
surfaceless context: yes
dmabuf support: modifiers
[17:00:16.029] GL version: OpenGL ES 3.2 v1.g13p0-01eac0.98c5dad4e3309b873e3189000b74ea36
[17:00:16.029] GLSL version: OpenGL ES GLSL ES 3.20
[17:00:16.029] GL vendor: ARM
[17:00:16.029] GL renderer: Mali-G52
[17:00:17.505] GL ES 3.2 - renderer features:
read-back format: ARGB8888
glReadPixels supports y-flip: no
wl_shm 10 bpc formats: yes
wl_shm 16 bpc formats: no
wl_shm half-float formats: no
internal R and RG formats: yes
OES_EGL_image_external: yes
wl_shm sub-image to texture: yes
[17:00:17.506] Using GL renderer
[17:00:17.637] event2 - adc-keys: is tagged by udev as: Keyboard
[17:00:17.637] event2 - adc-keys: device is a keyboard
[17:00:17.639] event1 - rk805 pwrkey: is tagged by udev as: Keyboard
[17:00:17.639] event1 - rk805 pwrkey: device is a keyboard
[17:00:17.640] event0 - hdmi_cec_key: is tagged by udev as: Keyboard
[17:00:17.640] event0 - hdmi_cec_key: device is a keyboard
[17:00:17.642] event3 - rk-headset: is tagged by udev as: Keyboard
[17:00:17.642] event3 - rk-headset: device is a keyboard
[17:00:17.806] libinput: configuring device "adc-keys".
[17:00:17.806] libinput: configuring device "rk805 pwrkey".
[17:00:17.806] libinput: configuring device "hdmi_cec_key".
[17:00:17.806] libinput: configuring device "rk-headset".
[17:00:17.807] Registered plugin API 'weston_drm_output_api_v1' of size 40
[17:00:17.807] Color manager: no-op
[17:00:17.807] Compositor capabilities:
arbitrary surface rotation: yes
screen capture uses y-flip: yes
cursor planes: yes
arbitrary resolutions: no
view mask clipping: yes
explicit sync: yes
color operations: no
presentation clock: CLOCK_MONOTONIC, id 1
presentation clock resolution: 0.000000001 s
[17:00:17.809] Loading module '/usr/lib/weston/desktop-shell.so'
[17:00:17.816] DRM: head 'HDMI-A-1' found, connector 114 is disconnected.
[17:00:17.816] Output 'DUMMY' attempts EOTF mode: SDR
[17:00:17.816] Output 'DUMMY' using color profile: stock sRGB color profile
[17:00:17.817] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[17:00:17.817] Output 'DUMMY' enabled with head(s) DUMMY
[17:00:17.817] launching '/usr/libexec/weston-keyboard'
[17:00:17.821] launching '/usr/libexec/weston-desktop-shell'
Failed to process Wayland connection: Broken pipe
Failed to process Wayland connection: Broken pipe
failed to create display: Broken pipe
failed to create display: Broken pipe
[ 39.489184] vcc3v3_lcd0_n: disabling
[ 39.489273] vcc3v3_lcd1_n: disabling
[ 44.125790] rockchip-drm display-subsystem: [drm] fb0: rockchipdrmfb frame buffer device

root@rk3566-buildroot:/#
root@rk3566-buildroot:/#
root@rk3566-buildroot:/# poweroff
root@rk3566-buildroot:/# Stopping input-event-daemon: done
Starting mobilenet:OK
alsa-lib main.c:1541:(snd_use_case_mgr_open) error: failed to import hw:1 use case configuration -2
-i use default asound.conf
Not stop quntionstop auto-reboot finished
Stopping dnsmasq: OK
Stopping pulseaudio: E: [pulseaudio] main.c: Failed to kill daemon: No such process
OK
Stopping dropbear sshd: OK
stoping weston... killall: weston: no process killed
done.
Stopping ntpd: OK
Stopping dhcpcd...
no /sbin/dhcpcd found; none killed
killall: rkaiq_3A_server: no process killed
Stopping network: OK
Stopping bluetoothd: OK
Stopping Wi-Fi/BT...
Stopping iptables: OK
Stopping system message bus: done
Saving random seed: [ 56.058934] dwc3 fcc00000.dwc3: request 000000009965b507 was not queued to ep0out
[ 56.059091] android_work: did not send uevent (0 0 0000000000000000)
OK
Stopping irqbalance: OK
Stopping klogd: OK
Stopping syslogd: OK
no stop function
[ 56.175856] ffs_data_put(): freeing
umount: /var/log: target is busy.
umount: /run: target is busy.
[ 56.254365] EXT4-fs (mmcblk1p6): re-mounted. Opts: (null)
The system is going down NOW!
Sent SIGTERM to all processes
[ 56.273198] dwhdmi-rockchip fe0a0000.hdmi: Rate 0 missing; compute N dynamically
[ 56.274134] dwhdmi-rockchip fe0a0000.hdmi: Rate 0 missing; compute N dynamically
W: [pulseaudio] pid.c: Failed to open PID file '/tmp/pulse-emf4iocctq8s/pid': Read-only file system
W: [pulseaudio] pid.c: Failed to open PID file '/tmp/pulse-emf4iocctq8s/pid': Read-only file system
Sent SIGKILL to all processes
Requesting system poweroff
[ 58.275205] rk808 0-0020: reboot: not restore POWER_EN
[ 58.306245] mpp_rkvdec2 fdf80200.rkvdec: shutdown device
[ 58.311595] mpp_rkvdec2 fdf80200.rkvdec: shutdown success
[ 58.317032] mpp_rkvenc fdf40000.rkvenc: shutdown device
[ 58.322280] mpp_rkvenc fdf40000.rkvenc: shutdown success
[ 58.329237] Set signal voltage to initial state
[ 58.335831] fan53555-regulator 0-001c: fan53555..... reset
[ 58.342319] fan53555-regulator 0-001c: reset: force fan53555_reset ok!
[ 58.357616] [WLAN_RFKILL]: Enter rfkill_wlan_shutdown
[ 58.362713] [WLAN_RFKILL]: rockchip_wifi_power: 0
[ 58.367433] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[ 58.373284] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[ 58.379132] [WLAN_RFKILL]: wifi shut off power [GPIO-1-1]
[ 58.384545] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 0
[ 58.390605] mpp-iep2 fdef0000.iep: shutdown device
[ 58.395430] mpp-iep2 fdef0000.iep: shutdown success
[ 58.400371] mpp_vepu2 fdee0000.vepu: shutdown device
[ 58.405359] mpp_vepu2 fdee0000.vepu: shutdown success
[ 58.410542] mpp_jpgdec fded0000.jpegd: shutdown device
[ 58.415702] mpp_jpgdec fded0000.jpegd: shutdown success
[ 58.420999] mpp_vdpu2 fdea0400.vdpu: shutdown device
[ 58.425986] mpp_vdpu2 fdea0400.vdpu: shutdown success
[ 58.431389] xhci-hcd xhci-hcd.4.auto: remove, state 4
[ 58.436476] usb usb6: USB disconnect, device number 1
[ 58.442487] xhci-hcd xhci-hcd.4.auto: USB bus 6 deregistered
[ 58.448499] xhci-hcd xhci-hcd.4.auto: remove, state 4
[ 58.453609] usb usb5: USB disconnect, device number 1
[ 58.459838] xhci-hcd xhci-hcd.4.auto: USB bus 5 deregistered
[ 58.473325] reboot: Power down