当前位置： 首页 > wzjs >正文

网站的作用网站开发网站排名优化

wzjs 2025/9/14 12:03:11
网站的作用,网站开发网站排名优化,积积桶肤肤的免费软件大全,织梦网站识别飞书文档https://x509p6c8to.feishu.cn/docx/doxcnlzpIgj3gosCZufBTCZxlMb SPI说明 SPI是串行外设接口（Serial Peripheral Interface）的缩写，是一种高速的，全双工，同步的通信总线，并且在芯片的管脚上占用…

飞书文档https://x509p6c8to.feishu.cn/docx/doxcnlzpIgj3gosCZufBTCZxlMb

SPI说明

SPI是串行外设接口（Serial Peripheral Interface）的缩写，是一种高速的，全双工，同步的通信总线，并且在芯片的管脚上占用四根线。

参考源码位置

/home/kemp/work/esp/esp-idf/examples/peripherals/spi_master

源码下载方式参考：

源码下载方式

屏幕接口

SCLK IO25 SPI 串口通信时钟信号线。

SDI  IO26 SPI 串口通信数据信号线。

CS  IO27 片选，低电平有效。

D/C IO14 数据/命令 读写选择，高电平为数据，低电平为命令。

RES IO12 电子纸复位信号，低电平有效。

BUSY IO13 电子纸刷新时，BUSY 引脚发出忙信号给主 MCU，此时 MCU 无法对电子纸驱动 IC 进行读写操作；电子纸刷新完成后，BUSY 引脚发出闲置状态信号，此时 MCU 可以对 电子纸驱动 IC 进行读写操作。GDEW 系列电子纸 BUSY 引脚忙状态为高电平（GDEH 系列为低电平），BUSY 引脚空闲状态反之。

墨水屏原理

152*152个像素 19Byte=152Bit 19*152的数组

152*152    19BYTE   1BYTE=8BIT  0000 0000  1111 1111

更多屏幕相关手册

1.54寸电子纸屏/ 152x152分辨率电子纸/ 四灰阶/ 支持局部刷新电子墨水屏 GDEW0154T8D_电子纸屏-大连佳显电子有限公司

代码说明

SPI部分

SPI Master Driver - - ‒ ESP-IDF 编程指南 release-v4.1 文档

/* SPI Master exampleThis example code is in the Public Domain (or CC0 licensed, at your option.)Unless required by applicable law or agreed to in writing, thissoftware is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES ORCONDITIONS OF ANY KIND, either express or implied.
*/
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "esp_system.h"
#include "driver/spi_master.h"
#include "driver/gpio.h"#include "ds_gpio.h"//#define PIN_NUM_MISO 1  //屏幕只写不读，此引脚不用
#define PIN_NUM_MOSI 26
#define PIN_NUM_CLK  25
#define PIN_NUM_CS   27spi_device_handle_t spi;void spi_send_cmd(const uint8_t cmd)
{esp_err_t ret;spi_transaction_t t;//设置发送指令ds_gpio_set_screen_dc(0);//设置片选模块ds_gpio_set_screen_cs(0);memset(&t, 0, sizeof(t));       //Zero out the transaction// t.flags=SPI_TRANS_USE_TXDATA;t.length=8;                     //Command is 8 bitst.tx_buffer=&cmd;               //The data is the cmd itselft.user=(void*)0;                //D/C needs to be set to 0//发送指令ret=spi_device_polling_transmit(spi, &t);  //Transmit!//取消片选模块ds_gpio_set_screen_cs(1);assert(ret==ESP_OK);            //Should have had no issues.
}void spi_send_data(const uint8_t data)
{esp_err_t ret;spi_transaction_t t;//设置发送数据ds_gpio_set_screen_dc(1);//设置片选模块ds_gpio_set_screen_cs(0);memset(&t, 0, sizeof(t));       //Zero out the transactiont.length=8;                 //Len is in bytes, transaction length is in bits.t.tx_buffer=&data;               //Datat.user=(void*)1;                //D/C needs to be set to 1//发送数据ret=spi_device_polling_transmit(spi, &t);  //Transmit!//取消片选模块ds_gpio_set_screen_cs(1);assert(ret==ESP_OK);            //Should have had no issues.
}//This function is called (in irq context!) just before a transmission starts. It will
//set the D/C line to the value indicated in the user field.
void spi_pre_transfer_callback(spi_transaction_t *t)
{int dc=(int)t->user;printf("dc callback\n");ds_gpio_set_screen_dc(dc);
}void screen_spi_init(void)
{esp_err_t ret;//IO设置spi_bus_config_t buscfg={.miso_io_num = PIN_NUM_MISO,                // MISO信号线.mosi_io_num = PIN_NUM_MOSI,                // MOSI信号线.sclk_io_num = PIN_NUM_CLK,                 // SCLK信号线.quadwp_io_num = -1,                        // WP信号线，专用于QSPI的D2.quadhd_io_num = -1,                        // HD信号线，专用于QSPI的D3.max_transfer_sz = 64*8,                    // 最大传输数据大小};//速率 模式设置spi_device_interface_config_t devcfg={.clock_speed_hz=15*1000*1000,            //Clock out at 26 MHz.mode=0,                                //SPI mode 0.queue_size=7,                          //We want to be able to queue 7 transactions at a time// .pre_cb=spi_pre_transfer_callback,  //Specify pre-transfer callback to handle D/C line};//Initialize the SPI busret=spi_bus_initialize(HSPI_HOST, &buscfg, 0);ESP_ERROR_CHECK(ret);//Attach the LCD to the SPI busret=spi_bus_add_device(HSPI_HOST, &devcfg, &spi);ESP_ERROR_CHECK(ret);}void screen_spi_test(){spi_send_cmd(0x55);vTaskDelay(10 / portTICK_PERIOD_MS);spi_send_data(0x55);
}

屏幕驱动部分

注意：这里的代码和视频中不太一样，因为旧版本屏幕停产，更换了屏幕型号，下方代码为0154B-D67的屏幕驱动代码，和最新版本屏幕是一致的。

#include <string.h>
#include <stdio.h>#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "sdkconfig.h"#include "ds_screen.h"
#include "ds_gpio.h"
#include "ds_spi.h"
#include "ds_data_image.h"// Detection busy
static void lcd_chkstatus(void)
{int count = 0;unsigned char busy;while (1){busy = ds_gpio_get_screen_busy();busy = (busy & 0x01);//=1 BUSYif (busy == 0)break;vTaskDelay(10 / portTICK_PERIOD_MS);count++;if (count >= 1000){printf("---------------time out ---\n");break;}}
}static void init_display()
{vTaskDelay(10 / portTICK_PERIOD_MS);ds_gpio_set_screen_rst(0); // Module resetvTaskDelay(10 / portTICK_PERIOD_MS);ds_gpio_set_screen_rst(1);vTaskDelay(100 / portTICK_PERIOD_MS);lcd_chkstatus();spi_send_cmd(0x12); // SWRESETlcd_chkstatus();spi_send_cmd(0x01); // Driver output controlspi_send_data(0xC7);spi_send_data(0x00);spi_send_data(0x01);spi_send_cmd(0x11); // data entry modespi_send_data(0x01);spi_send_cmd(0x44); // set Ram-X address start/end positionspi_send_data(0x00);spi_send_data(0x18); // 0x0C-->(18+1)*8=200spi_send_cmd(0x45);  // set Ram-Y address start/end positionspi_send_data(0xC7); // 0xC7-->(199+1)=200spi_send_data(0x00);spi_send_data(0x00);spi_send_data(0x00);spi_send_cmd(0x3C); // BorderWavefromspi_send_data(0x05);spi_send_cmd(0x18); // Read built-in temperature sensorspi_send_data(0x80);spi_send_cmd(0x4E); // set RAM x address count to 0;spi_send_data(0x00);spi_send_cmd(0x4F); // set RAM y address count to 0X199;spi_send_data(0xC7);spi_send_data(0x00);vTaskDelay(100 / portTICK_PERIOD_MS);lcd_chkstatus();
}/Enter deep sleep mode
void deep_sleep(void) // Enter deep sleep mode
{spi_send_cmd(0x10); // enter deep sleepspi_send_data(0x01);vTaskDelay(100 / portTICK_PERIOD_MS);
}void refresh(void)
{spi_send_cmd(0x22); // Display Update Controlspi_send_data(0xF7);spi_send_cmd(0x20); // Activate Display Update Sequencelcd_chkstatus();
}void refresh_part(void)
{spi_send_cmd(0x22); // Display Update Controlspi_send_data(0xFF);spi_send_cmd(0x20); // Activate Display Update Sequencelcd_chkstatus();
}// 图片全刷-全白函数
static void ds_screen_display_white(void)
{unsigned int i, k;spi_send_cmd(0x24); // write RAM for black(0)/white (1)for (k = 0; k < 250; k++){for (i = 0; i < 25; i++){spi_send_data(0xff);}}
}// 图片全刷-数据函数
void ds_screen_full_display_data(const uint8_t *data)
{unsigned int i;spi_send_cmd(0x24); // write RAM for black(0)/white (1)for (i = 0; i < 5000; i++){spi_send_data(*data);data++;}
}// 全刷 不带数据
void ds_screen_full_display(void pic_display(void))
{init_display();pic_display(); // picturerefresh();     // EPD_refreshdeep_sleep();
}// 全刷 带数据
void ds_screen_full_display_bydata(void display_func(const uint8_t *data), const uint8_t *data)
{init_display();display_func(data); // picturerefresh();          // EPD_refreshdeep_sleep();
}// 局部刷 不带数据
void ds_screen_partial_display(unsigned int x_start, unsigned int y_start, void partial_new(void), unsigned int PART_COLUMN, unsigned int PART_LINE)
{unsigned int i;unsigned int x_end, y_start1, y_start2, y_end1, y_end2;x_start = x_start / 8;x_end = x_start + PART_LINE / 8 - 1;y_start1 = 0;y_start2 = 200 - y_start;if (y_start >= 256){y_start1 = y_start2 / 256;y_start2 = y_start2 % 256;}y_end1 = 0;y_end2 = y_start2 + PART_COLUMN - 1;if (y_end2 >= 256){y_end1 = y_end2 / 256;y_end2 = y_end2 % 256;}// Add hardware reset to prevent background color changeds_gpio_set_screen_rst(0); // Module resetvTaskDelay(10 / portTICK_PERIOD_MS);ds_gpio_set_screen_rst(1);vTaskDelay(10 / portTICK_PERIOD_MS);// Lock the border to prevent flashingspi_send_cmd(0x3C); // BorderWavefrom,spi_send_data(0x80);spi_send_cmd(0x44);      // set RAM x address start/end, in page 35spi_send_data(x_start);  // RAM x address start at 00h;spi_send_data(x_end);    // RAM x address end at 0fh(15+1)*8->128spi_send_cmd(0x45);      // set RAM y address start/end, in page 35spi_send_data(y_start2); // RAM y address start at 0127h;spi_send_data(y_start1); // RAM y address start at 0127h;spi_send_data(y_end2);   // RAM y address end at 00h;spi_send_data(y_end1);   // ????=0spi_send_cmd(0x4E); // set RAM x address count to 0;spi_send_data(x_start);spi_send_cmd(0x4F); // set RAM y address count to 0X127;spi_send_data(y_start2);spi_send_data(y_start1);spi_send_cmd(0x24); // Write Black and White image to RAMpartial_new();refresh_part();deep_sleep();
}// 局部刷 带数据
void ds_screen_partial_display_bydata(unsigned int x_start, unsigned int y_start,void partial_new(const uint8_t *data), const uint8_t *new_data,unsigned int PART_COLUMN, unsigned int PART_LINE)
{printf("x_start=%d x_end=%d y_start=%d y_end=%d\n", x_start, y_start, PART_COLUMN, PART_LINE);unsigned int i;unsigned int x_end, y_start1, y_start2, y_end1, y_end2;x_start = x_start / 8;x_end = x_start + PART_LINE / 8 - 1;y_start1 = 0;y_start2 = 200 - y_start;if (y_start >= 256){y_start1 = y_start2 / 256;y_start2 = y_start2 % 256;}y_end1 = 0;y_end2 = y_start2 + PART_COLUMN - 1;if (y_end2 >= 256){y_end1 = y_end2 / 256;y_end2 = y_end2 % 256;}// Add hardware reset to prevent background color changeds_gpio_set_screen_rst(0); // Module resetvTaskDelay(10 / portTICK_PERIOD_MS);ds_gpio_set_screen_rst(1);vTaskDelay(10 / portTICK_PERIOD_MS);// Lock the border to prevent flashingspi_send_cmd(0x3C); // BorderWavefrom,spi_send_data(0x80);spi_send_cmd(0x44);      // set RAM x address start/end, in page 35spi_send_data(x_start);  // RAM x address start at 00h;spi_send_data(x_end);    // RAM x address end at 0fh(15+1)*8->128spi_send_cmd(0x45);      // set RAM y address start/end, in page 35spi_send_data(y_start2); // RAM y address start at 0127h;spi_send_data(y_start1); // RAM y address start at 0127h;spi_send_data(y_end2);   // RAM y address end at 00h;spi_send_data(y_end1);   // ????=0spi_send_cmd(0x4E); // set RAM x address count to 0;spi_send_data(x_start);spi_send_cmd(0x4F); // set RAM y address count to 0X127;spi_send_data(y_start2);spi_send_data(y_start1);spi_send_cmd(0x24); // Write Black and White image to RAMpartial_new(new_data);
}uint8_t partial_data[200][25];
uint8_t partial_data_array[5000];void ds_screen_partial_data_init()
{for (int index = 0; index < 200; index++){for (int yindex = 0; yindex < 25; yindex++){partial_data[index][yindex] = 0xff;}}
}void ds_screen_partial_data_add(unsigned int x_start, unsigned int x_end, unsigned int y_start, unsigned int y_end, const uint8_t *data)
{uint8_t x_len = x_end - x_start;// uint8_t y_len = y_end - y_start;uint8_t x_data_location = x_start / 8;uint8_t x_size = x_len / 8;int data_index = 0;// int move = x_start % 8;if (x_start % 8 != 0){x_data_location++;}if (x_len % 8 != 0){x_size++;}for (int x_index = y_start; x_index < y_end; x_index++){for (int y_index = x_data_location; y_index < (x_data_location + x_size); y_index++){partial_data[x_index][y_index] = (~data[data_index]);data_index++;}}
}// 图片全刷-全白函数
static void ds_screen_display_data(void)
{unsigned int i;spi_send_cmd(0x24);for (i = 0; i < 5000; i++){spi_send_data(partial_data_array[i]);}spi_send_cmd(0x26);for (i = 0; i < 5000; i++){spi_send_data(partial_data_array[i]);}
}// 局刷数据-复制
void ds_screen_partial_data_copy()
{int data_index = 0;for (int index = 0; index < 200; index++){for (int yindex = 0; yindex < 25; yindex++){partial_data_array[data_index] = partial_data[index][yindex];data_index++;}}ds_screen_full_display(ds_screen_display_data);
}// 接口初始化
void init_screen_interface()
{ds_screen_gpio_init();screen_spi_init();
}// 清屏为白色
void ds_screen_clean_white()
{ds_screen_init();vTaskDelay(2000 / portTICK_PERIOD_MS);
}// 初始化
void ds_screen_init()
{ds_screen_full_display(ds_screen_display_white); // EPD_sleep
}

参考：

【科普贴】SPI接口详解_湉湉家的小虎子的博客-CSDN博客_spi

1.54寸高频刷新 快刷1.5秒电子墨水屏 分辨率200x200 SPI串口 GDEY0154D67_电子墨水屏幕-大连佳显电子


文章转载自：

http://VGV3fgdR.bqmsm.cn
http://u4zQJd9v.bqmsm.cn
http://iaf1e3Y5.bqmsm.cn
http://HLJ3xW72.bqmsm.cn
http://J6elt0s1.bqmsm.cn
http://u0hVab3L.bqmsm.cn
http://Z2AyOLYQ.bqmsm.cn
http://iPMsQZmr.bqmsm.cn
http://gtjoxMNi.bqmsm.cn
http://ScV6OpFA.bqmsm.cn
http://lSWgZqeW.bqmsm.cn
http://Xowncu01.bqmsm.cn
http://FNhvnYEm.bqmsm.cn
http://ptiYfhM1.bqmsm.cn
http://IH4T52Y9.bqmsm.cn
http://GkyqtGnh.bqmsm.cn
http://CLbRKJ1x.bqmsm.cn
http://CUusLQAC.bqmsm.cn
http://0rboyKX7.bqmsm.cn
http://nHFKelwv.bqmsm.cn
http://EffKRXW2.bqmsm.cn
http://rClaLTzO.bqmsm.cn
http://vQFvwe9Q.bqmsm.cn
http://onFxAy3u.bqmsm.cn
http://p3Yot9YN.bqmsm.cn
http://zIutdUG7.bqmsm.cn
http://qzCsNLlo.bqmsm.cn
http://o6vvMw4V.bqmsm.cn
http://82RRF3Fo.bqmsm.cn
http://qi1Smkk4.bqmsm.cn
http://www.dtcms.com/wzjs/729546.html

相关文章：

  • 建设部施工安全管理网站自己做的网站搜索引擎搜不到
  • 音乐网站建设策划书wordpress获取最新发布列表
  • 网站质作wordpress登入页面
  • 企业商务网站设计与开发站长是什么级别
  • 成品网站是什么意思个人网站的版权怎么写
  • 网站使用支付接口如何收费网站开发属于购销合同
  • 网站开发的层次黄骅网站建设公司
  • 化妆品企业网站源码视觉做的比较好的国外网站
  • ppt 如何做网站交互式如何做网站英文简历模板
  • 网站开发实战作业答案wordpress爱搭配
  • 易县网站建设wordpress最强的教育网站
  • 国外网站网页设计兰州装修公司哪家好
  • 商务网站建设的一般流程是什么?私人信息调查
  • 网站优化推广服务wordpress开发框架
  • 网站改版建设征求意见书佛山市网站公司
  • 国外活动策划网站电子商务网站建设 李洪心
  • 网站备案密码忘wordpress虚化主题
  • 甲蛙网站建设建筑工程网上备案流程
  • 电商网站开发工作室东莞网站设计公司淘宝
  • 商城顺德网站建设pc网站建设建议
  • 秦皇岛建设网站公司哪家好手机可以创建网站吗
  • 前端如何做双语网站网站设计答辩ppt
  • 绍兴手机网站建设东陵网站制作
  • 学校能建设网站吗亚洲足球最新排名
  • 四字母域名建设网站可以吗免费的网页设计成品详解
  • 怎么让自己做的网站让别人看到手机网站范例
  • 做网站的图片字虚外贸公司网站多少钱
  • 天津做流产五洲网站北京网站建设华网天下
  • wordpress国主题公园搜索引擎优化员简历
  • 搭建flv视频网站嘉兴网站开发选哪家