嘉定华亭网站建设北京网络推广公司wyhseo
0x0 上位机状态
1.成品模式下测试流程分为哪几种状态呢？在这个状态下[上位机程序]和[下位机]或者用户进行什么样的沟通交流呢？①Configuration Status 在这个状态下用户可以进行配置选项的修改和保存，程序工作前的准备操作
②Testing Status （1）serial port recognition status [上位机程序]去识别有没有[下位机dongle]设备的存在（2）scan prepare connect status [上位机程序]发送一系列的指令去获取遥控器的MAC地址（遥控器[必须]在5s内进入广播模式）（3）connect status [上位机程序]通过发送一系列的指令去[连接RC和获取遥控器版本信息](4) audio button test status
③Test Stop Deal Status 清除配对信息，和断开连接，保存测试结果
④Program exit Status 程序进行退出前的资源释放等处理
0x1 现象分析
测试中出现
遥控器连接不上
0x2 日志分析
可能的情况：
①RC没有进行广播行为
②RC有广播行为，但是与dongle距离太远或者中间有障碍物，导致了数据在指定时间内无法通过蓝牙传输给dongle
连接不上的日志
INFO 2023-11-25T16:11:12.900 C(click behavior): Start Test
INFO 2023-11-25T16:11:12.900 C: Entering Testing StatusINFO 2023-11-25T16:11:12.900 V(Func Rc): Enter serial port recognition status true false
INFO 2023-11-25T16:11:12.901 C: 成品模式 true
DEBUG 2023-11-25T16:11:12.901 C: have already identified it.
INFO 2023-11-25T16:11:12.901 C: End of serial port recognition status ret [ 0 ] INFO 2023-11-25T16:11:12.901 C: Enter scan prepare connect status
DEBUG 2023-11-25T16:11:12.904 C: WriteData( "reset\r\n" )
DEBUG 2023-11-25T16:11:13.686 P: m_buffer data: "ff000200000001"
DEBUG 2023-11-25T16:11:13.686 C: recv(reset)
DEBUG 2023-11-25T16:11:13.688 C: WriteData( "clear_bond 0\r\n" )
DEBUG 2023-11-25T16:11:13.695 P: m_buffer data: "ff00020009000a"
DEBUG 2023-11-25T16:11:13.695 C: recv(clear_bond_0)
DEBUG 2023-11-25T16:11:13.696 C: WriteData( "scan_start\r\n" )
DEBUG 2023-11-25T16:11:13.698 P: m_buffer data: "ff000200020003"
DEBUG 2023-11-25T16:11:13.698 C: recv(scan_start)
WARN 2023-11-25T16:11:18.703 C(m_scanCheck): m_scanCheck failed, scan_stop, and stopTest.
DEBUG 2023-11-25T16:11:18.706 P: m_buffer data: "ff000200030004"
ERROR 2023-11-25T16:11:18.706 C(Remote control does not have pairing behavior): End of scan prepare connect status DEBUG 2023-11-25T16:11:18.707 C: recv(scan_stop)
DEBUG 2023-11-25T16:11:18.712 C: End of Test Stop Deal StatusINFO 2023-11-25T16:11:25.870 V(close behavior) Entering Program exit status
连接的上的日志
INFO 2023-11-25T16:14:10.965 C(click behavior): Start Test
INFO 2023-11-25T16:14:10.966 C: Entering Testing StatusINFO 2023-11-25T16:14:10.966 V(Func Rc): Enter serial port recognition status true false
INFO 2023-11-25T16:14:10.966 C: 成品模式 true
DEBUG 2023-11-25T16:14:10.967 C: have already identified it.
INFO 2023-11-25T16:14:10.967 C: End of serial port recognition status ret [ 0 ] INFO 2023-11-25T16:14:10.967 C: Enter scan prepare connect status
DEBUG 2023-11-25T16:14:10.968 C: WriteData( "reset\r\n" )
DEBUG 2023-11-25T16:14:11.744 P: m_buffer data: "ff000200000001"
DEBUG 2023-11-25T16:14:11.744 C: recv(reset)
DEBUG 2023-11-25T16:14:11.746 C: WriteData( "clear_bond 0\r\n" )
DEBUG 2023-11-25T16:14:11.754 P: m_buffer data: "ff00020009000a"
DEBUG 2023-11-25T16:14:11.754 C: recv(clear_bond_0)
DEBUG 2023-11-25T16:14:11.754 C: WriteData( "scan_start\r\n" )
DEBUG 2023-11-25T16:14:11.757 P: m_buffer data: "ff000200020003"
DEBUG 2023-11-25T16:14:11.757 C: recv(scan_start)
DEBUG 2023-11-25T16:14:11.792 P: m_buffer data: "ff010d00cf000701007bae304d4920524388ff012300df000701007bae30e5b0"
DEBUG 2023-11-25T16:14:11.792 scan_ret data: "cf000701007bae304d49205243"
DEBUG 2023-11-25T16:14:11.792 C: curRssi -49 m_rssiVal -50
DEBUG 2023-11-25T16:14:11.792 C: rc_mac_addr_type[ "00" ] rc_mac_addr[ "30:ae:7b:00:01:07" ] rc_ble_name[ "MI RC" ]
DEBUG 2023-11-25T16:14:11.793 C: WriteData(scan_stop)
INFO 2023-11-25T16:14:11.795 C(Remote control pairing behavior): End of scan prepare connect status INFO 2023-11-25T16:14:11.796 C: Enter connect status
DEBUG 2023-11-25T16:14:11.796 C: recv(scan_stop)
DEBUG 2023-11-25T16:14:11.796 C: WriteData( "connect 00 30:ae:7b:00:01:07\r\n" )
DEBUG 2023-11-25T16:14:11.872 P: m_buffer data: "ff0009000400000701007bae306d"
DEBUG 2023-11-25T16:14:11.873 C: recv(connect)
DEBUG 2023-11-25T16:14:12.877 C: WriteData(sw_get) 1
DEBUG 2023-11-25T16:14:12.882 P: m_buffer data: "ff000200060007"
DEBUG 2023-11-25T16:14:12.882 C: recv(sw_get)
DEBUG 2023-11-25T16:14:13.242 P: m_buffer data: "ff040700412e342e302e3871"
DEBUG 2023-11-25T16:14:13.245 C: rc_software_version[ "A408" ]
INFO 2023-11-25T16:14:13.245 C: End of connect status INFO 2023-11-25T16:14:13.245 C: Enter function(audio button) test status
INFO 2023-11-25T16:15:22.132 V(close behavior) Entering Program exit status