当前位置：首页 > wzjs >正文

p2p视频网站建设深圳市龙华区

wzjs 2025/8/11 20:53:13

p2p视频网站建设,深圳市龙华区,做购物网站哪个cms好用,做网站的相关术语INA219电流、电压、功率测量芯片应用简述芯片引脚应用电路寄存器驱动代码简述 ‌INA219是一款由德州仪器（Texas Instruments）生产的高精度电流/功率监测芯片，广泛应用于电池监控、电源管理等需要精确电流和功率测量的应用中‌‌。该芯片通…

INA219电流、电压、功率测量芯片应用

简述
芯片引脚
应用电路
寄存器
驱动代码

简述

‌INA219是一款由德州仪器（Texas Instruments）生产的高精度电流/功率监测芯片，广泛应用于电池监控、电源管理等需要精确电流和功率测量的应用中‌‌。该芯片通过I2C总线接口与微控制器进行通信，能够实时监测负载电流、电压和功率等参数。

技术参数：

电压测量范围‌：0V到26V，适用于广泛的应用场景‌。
电流测量范围‌：通过外部电流检测电阻，可测量的电流范围一般从0A到3.2A或更高‌。
功率计算范围‌：根据测量的电压和电流决定，单位为瓦特‌。
分辨率‌：电流分辨率最高可达0.1mA，电压分辨率最高可达0.1mV‌。

特点和应用场景
INA219具有以下特点：

高精度‌：能够提供高精度的电流和电压测量。
低功耗‌：适用于需要低功耗的应用场景。
多种型号‌：包括INA219A、INA219B和INA219C，每个型号有不同的特点和适用场景‌ 。

常见型号及其特点：

INA219A‌：适用于一般低功耗应用，具有较高的电流测量精度和较低的偏置电流‌。
INA219B‌：具有更低的功耗，并且在电流测量方面提供更高的精度，适用于需要高精度电流监控的系统‌。
INA219C‌：提供较宽的工作电压范围和更高的电流量程，适用于更高电流范围的监测应用‌。

芯片引脚

在这里插入图片描述

IN+和IN_：分别是接检测分流电阻的两端。
GND：接电源负极
Vs：电源正极（电压范围：3-5.5V）
SCL：通讯时钟线
SDA：通讯数据线
A0和A1：地址选择引脚（地址对应表如下图）

应用电路

配置用于检测分流和总线电压：

分流电压：指的是分流电阻 $R_{SHUNT}$ 两端的电压。
总线电压：指的是 $V_{IN-}$ 和GND之间的电压。

在这里插入图片描述

带有输入滤波的应用电路：

寄存器

INA219通信协议使用的是I2C总线协议，16bit寄存器即2个字节。一共有6个寄存器,其中只需要设置00h和05h两个寄存器，其他为只读寄存器：

00：配置寄存器，主要用来配置INA219的工作方式和配置参数（读/写）
01：分流电阻电压寄存器（只读）
02：总线电压寄存器 $V_{IN-}$ 和GND之间的电压（只读）
03：功率寄存器（只读）
04：电流寄存器（只读）
05：校准寄存器（读/写）
RST：Bit 15复位位，设置为1产生系统复位，就像上电复位一样，所有寄存器复位成默认值。该位自清零。
BRNG：Bit 13总线电压量程范围，0=16V，1=32V（默认值）
PG：Bits[11, 12] PGA(设置分流电阻最大的电压，用于计算最大检测电流)：

BADC: Bits[7-10]总线电压ADC分辨率/平均值设置（总线电压寄存器02h）
SADC: Bits[3-6]分压电阻电压ADC分辨率/平均值设置（分流电压寄存器01h）

MODE: Bit[0-2]运行模式

数据输出寄存器：
分流电压寄存器（01h）:
总线电压寄存器（02h）:
CNVR：Bit 1 转换完成为1表示转换完成。
OVF: Bit 0 数学溢出标志位，为1表示功率或电流计算结果溢出，指示电流或功率寄存器数据可能无意义。
功率寄存器（03h）
电流寄存器（04h）
校准寄存器（05h）

校准值计算：
校准值可通过如下公式计算：

首先确定分流电阻 $R_{SHUNT}$ 的阻值=0.1R，设置最大检测电压为：32V，设置分流电阻电压范围：320mV
所以最大检测电流 $I_{MAX}$ =320mV/0.1R=0.32V/0.1R=3.2A
Current_LSB_MIN= $I_{MAX}/2^{15}$ =3.2/23767=0.00009766 ADC@15bit
Current_LSB_MAX= $I_{MAX}/2^{12}$ =3.2/4096=0.00078125 ADC@12bit
Current_LSB的选值范围为Current_LSB_MIN和Current_LSB_MAX之间，选择靠近Current_LSB_MIN
因此这里选择Current_LSB=10010^-6=100uA=0.0001A（每bit位对应的电流大小）
计算基准值：Cal=0.04096/(Current_LSB/R)=0.04096/(0.0001A0.1R)=4096=0x1000
当配置05寄存器的值为：0x1000

但是这样配置完后发现测量到的电流值不对，官方手册还给出了Cal的校准公式：
在这里插入图片描述
用电流表测到的实际值为0.290A，INA219测量结果为0.342A，
校准后的cal=4096*0.290/0.3421 = 3472 = 0x0D90
设置后的测量值正确

计算功率LSB
P_LSB=20I_LSB=200.0001A=0.002W
在这里插入图片描述

驱动代码

Type_def.h

typedef signed char   s8;     //  8 bits 
typedef signed int    s16;    // 16 bits 
typedef signed long   s32;    // 32 bits typedef unsigned char   u8;     //  8 bits 
typedef unsigned int    u16;    // 16 bits 
typedef unsigned long   u32;    // 32 bits typedef signed char     int8;   //  8 bits 
typedef signed int      int16;  // 16 bits 
typedef signed long     int32;  // 32 bits typedef unsigned char   uint8;  //  8 bits 
typedef unsigned int    uint16; // 16 bits 
typedef unsigned long   uint32; // 32 bits typedef signed char     int8_t;   //  8 bits 
typedef signed int      int16_t;  // 16 bits 
typedef signed long     int32_t;  // 32 bits typedef unsigned char   uint8_t;  //  8 bits 
typedef unsigned int    uint16_t; // 16 bits 
typedef unsigned long   uint32_t; // 32 bits

drv_ina219.h

#ifndef __DRV_INA219_H__
#define __DRV_INA219_H__// I2C Address Options
#define INA219_I2C_ADDRESS_CONF_0               (u8)(0x40 << 1)     // A0 = GND, A1 = GND
#define INA219_I2C_ADDRESS_CONF_1               (u8)(0x41 << 1)     // A0 = VS+, A1 = GND
#define INA219_I2C_ADDRESS_CONF_2               (u8)(0x42 << 1)     // A0 = SDA, A1 = GND
#define INA219_I2C_ADDRESS_CONF_3               (u8)(0x43 << 1)     // A0 = SCL, A1 = GND
#define INA219_I2C_ADDRESS_CONF_4               (u8)(0x44 << 1)     // A0 = GND, A1 = VS+
#define INA219_I2C_ADDRESS_CONF_5               (u8)(0x45 << 1)     // A0 = VS+, A1 = VS+
#define INA219_I2C_ADDRESS_CONF_6               (u8)(0x46 << 1)     // A0 = SDA, A1 = VS+
#define INA219_I2C_ADDRESS_CONF_7               (u8)(0x47 << 1)     // A0 = SCL, A1 = VS+
#define INA219_I2C_ADDRESS_CONF_8               (u8)(0x48 << 1)     // A0 = GND, A1 = SDA
#define INA219_I2C_ADDRESS_CONF_9               (u8)(0x49 << 1)     // A0 = VS+, A1 = SDA
#define INA219_I2C_ADDRESS_CONF_A               (u8)(0x4A << 1)     // A0 = SDA, A1 = SDA
#define INA219_I2C_ADDRESS_CONF_B               (u8)(0x4B << 1)     // A0 = SCL, A1 = SDA
#define INA219_I2C_ADDRESS_CONF_C               (u8)(0x4C << 1)     // A0 = GND, A1 = SCL
#define INA219_I2C_ADDRESS_CONF_D               (u8)(0x4D << 1)     // A0 = VS+, A1 = SCL
#define INA219_I2C_ADDRESS_CONF_E               (u8)(0x4E << 1)     // A0 = SDA, A1 = SCL
#define INA219_I2C_ADDRESS_CONF_F               (u8)(0x4F << 1)     // A0 = SCL, A1 = SCL
#define INA219_I2C_ADDRESS                      INA219_I2C_ADDRESS_CONF_0/*----------------------------------------------------------------------------*/
// Register Addresses
#define INA219_REG_CONFIG                       (u8)(0x00)      // CONFIG REGISTER (R/W)
#define INA219_REG_SHUNTVOLTAGE                 (u8)(0x01)      // SHUNT VOLTAGE REGISTER (R)
#define INA219_REG_BUSVOLTAGE                   (u8)(0x02)      // BUS VOLTAGE REGISTER (R)
#define INA219_REG_POWER                        (u8)(0x03)      // POWER REGISTER (R)
#define INA219_REG_CURRENT                      (u8)(0x04)      // CURRENT REGISTER (R)
#define INA219_REG_CALIBRATION                  (u8)(0x05)      // CALIBRATION REGISTER (R/W)/*----------------------------------------------------------------------------*/
// Macros for assigning config bits
#define INA219_CFGB_RESET(x)                    (u16)((x & 0x01) << 15)     // Reset Bit
#define INA219_CFGB_BUSV_RANGE(x)               (u16)((x & 0x01) << 13)     // Bus Voltage Range
#define INA219_CFGB_PGA_RANGE(x)                (u16)((x & 0x03) << 11)     // Shunt Voltage Range
#define INA219_CFGB_BADC_RES_AVG(x)             (u16)((x & 0x0F) << 7)      // Bus ADC Resolution/Averaging
#define INA219_CFGB_SADC_RES_AVG(x)             (u16)((x & 0x0F) << 3)      // Shunt ADC Resolution/Averaging
#define INA219_CFGB_MODE(x)                     (u16) (x & 0x07)            // Operating Mode/*----------------------------------------------------------------------------*/
// Configuration Register
#define INA219_CFG_RESET                        INA219_CFGB_RESET(1)            // Reset Bit#define INA219_CFG_BVOLT_RANGE_MASK             INA219_CFGB_BUSV_RANGE(1)       // Bus Voltage Range Mask
#define INA219_CFG_BVOLT_RANGE_16V              INA219_CFGB_BUSV_RANGE(0)       // 0-16V Range
#define INA219_CFG_BVOLT_RANGE_32V              INA219_CFGB_BUSV_RANGE(1)       // 0-32V Range (default)#define INA219_CFG_SVOLT_RANGE_MASK             INA219_CFGB_PGA_RANGE(3)        // Shunt Voltage Range Mask
#define INA219_CFG_SVOLT_RANGE_40MV             INA219_CFGB_PGA_RANGE(0)        // Gain 1, 40mV Range
#define INA219_CFG_SVOLT_RANGE_80MV             INA219_CFGB_PGA_RANGE(1)        // Gain 2, 80mV Range
#define INA219_CFG_SVOLT_RANGE_160MV            INA219_CFGB_PGA_RANGE(2)        // Gain 4, 160mV Range
#define INA219_CFG_SVOLT_RANGE_320MV            INA219_CFGB_PGA_RANGE(3)        // Gain 8, 320mV Range (default)#define INA219_CFG_BADCRES_MASK                 INA219_CFGB_BADC_RES_AVG(15)    // Bus ADC Resolution and Averaging Mask
#define INA219_CFG_BADCRES_9BIT_1S_84US         INA219_CFGB_BADC_RES_AVG(0)     // 1 x 9-bit Bus sample
#define INA219_CFG_BADCRES_10BIT_1S_148US       INA219_CFGB_BADC_RES_AVG(1)     // 1 x 10-bit Bus sample
#define INA219_CFG_BADCRES_11BIT_1S_276US       INA219_CFGB_BADC_RES_AVG(2)     // 1 x 11-bit Bus sample
#define INA219_CFG_BADCRES_12BIT_1S_532US       INA219_CFGB_BADC_RES_AVG(3)     // 1 x 12-bit Bus sample (default)
#define INA219_CFG_BADCRES_12BIT_2S_1MS         INA219_CFGB_BADC_RES_AVG(9)     // 2 x 12-bit Bus samples averaged together
#define INA219_CFG_BADCRES_12BIT_4S_2MS         INA219_CFGB_BADC_RES_AVG(10)    // 4 x 12-bit Bus samples averaged together
#define INA219_CFG_BADCRES_12BIT_8S_4MS         INA219_CFGB_BADC_RES_AVG(11)    // 8 x 12-bit Bus samples averaged together
#define INA219_CFG_BADCRES_12BIT_16S_8MS        INA219_CFGB_BADC_RES_AVG(12)    // 16 x 12-bit Bus samples averaged together
#define INA219_CFG_BADCRES_12BIT_32S_17MS       INA219_CFGB_BADC_RES_AVG(13)    // 32 x 12-bit Bus samples averaged together
#define INA219_CFG_BADCRES_12BIT_64S_34MS       INA219_CFGB_BADC_RES_AVG(14)    // 64 x 12-bit Bus samples averaged together
#define INA219_CFG_BADCRES_12BIT_128S_68MS      INA219_CFGB_BADC_RES_AVG(15)    // 128 x 12-bit Bus samples averaged together#define INA219_CFG_SADCRES_MASK                 INA219_CFGB_SADC_RES_AVG(15)    // Shunt ADC Resolution and Averaging Mask
#define INA219_CFG_SADCRES_9BIT_1S_84US         INA219_CFGB_SADC_RES_AVG(0)     // 1 x 9-bit Shunt sample
#define INA219_CFG_SADCRES_10BIT_1S_148US       INA219_CFGB_SADC_RES_AVG(1)     // 1 x 10-bit Shunt sample
#define INA219_CFG_SADCRES_11BIT_1S_276US       INA219_CFGB_SADC_RES_AVG(2)     // 1 x 11-bit Shunt sample
#define INA219_CFG_SADCRES_12BIT_1S_532US       INA219_CFGB_SADC_RES_AVG(3)     // 1 x 12-bit Shunt sample (default)
#define INA219_CFG_SADCRES_12BIT_2S_1MS         INA219_CFGB_SADC_RES_AVG(9)     // 2 x 12-bit Shunt samples averaged together
#define INA219_CFG_SADCRES_12BIT_4S_2MS         INA219_CFGB_SADC_RES_AVG(10)    // 4 x 12-bit Shunt samples averaged together
#define INA219_CFG_SADCRES_12BIT_8S_4MS         INA219_CFGB_SADC_RES_AVG(11)    // 8 x 12-bit Shunt samples averaged together
#define INA219_CFG_SADCRES_12BIT_16S_8MS        INA219_CFGB_SADC_RES_AVG(12)    // 16 x 12-bit Shunt samples averaged together
#define INA219_CFG_SADCRES_12BIT_32S_17MS       INA219_CFGB_SADC_RES_AVG(13)    // 32 x 12-bit Shunt samples averaged together
#define INA219_CFG_SADCRES_12BIT_64S_34MS       INA219_CFGB_SADC_RES_AVG(14)    // 64 x 12-bit Shunt samples averaged together
#define INA219_CFG_SADCRES_12BIT_128S_68MS      INA219_CFGB_SADC_RES_AVG(15)    // 128 x 12-bit Shunt samples averaged together#define INA219_CFG_MODE_MASK                    INA219_CFGB_MODE(7)             // Operating Mode Mask
#define INA219_CFG_MODE_POWERDOWN               INA219_CFGB_MODE(0)             // Power-Down
#define INA219_CFG_MODE_SVOLT_TRIGGERED         INA219_CFGB_MODE(1)             // Shunt Voltage, Triggered
#define INA219_CFG_MODE_BVOLT_TRIGGERED         INA219_CFGB_MODE(2)             // Bus Voltage, Triggered
#define INA219_CFG_MODE_SANDBVOLT_TRIGGERED     INA219_CFGB_MODE(3)             // Shunt and Bus, Triggered
#define INA219_CFG_MODE_ADCOFF                  INA219_CFGB_MODE(4)             // ADC Off (disabled)
#define INA219_CFG_MODE_SVOLT_CONTINUOUS        INA219_CFGB_MODE(5)             // Shunt Voltage, Continuous
#define INA219_CFG_MODE_BVOLT_CONTINUOUS        INA219_CFGB_MODE(6)             // Bus Voltage, Continuous
#define INA219_CFG_MODE_SANDBVOLT_CONTINUOUS    INA219_CFGB_MODE(7)             // Shunt and Bus, Continuous (default)/*----------------------------------------------------------------------------*/
// Bus Voltage Register
#define INA219_BVOLT_CNVR                       (u16)(0x0002)       // Conversion Ready
#define INA219_BVOLT_OVF                        (u16)(0x0001)       // Math Overflow Flagstruct ina219_value_t
{s16 voltage;s32 shunt;s32 current;s32 power;
};void drv_ina219_init(void);s16 ina219_GetBusVoltage_mV(void);s32 ina219_GetShuntVoltage_uV(void);s32 ina219_GetCurrent_uA(void);s32 ina219_GetPower_mW(void);void ina219_process(void);#endif //__DRV_INA219_H__

drv_ina219.c

#include "config.h"
#include "debug.h"
#include "app_config.h"#include "STC32G_Timer.h"
#include "STC32G_GPIO.h"
#include "STC32G_NVIC.h"
#include "STC32G_Exti.h"
#include "STC32G_I2C.h"
#include "STC32G_Delay.h"
#include "STC32G_Switch.h"#include "drv_ina219.h"#if TCFG_DRV_INA219_SUPPORTstruct ina219_value_t ina219_value;u16 ina219_calValue = 0;u8  ina219_busVolt_LSB_mV = 4;      // Bus Voltage LSB value = 4mV
u8  ina219_shuntVolt_LSB_uV = 10;   // Shunt Voltage LSB value = 10uVu32 ina219_current_LSB_uA;
u32 ina219_power_LSB_mW;/*** @brief   INA219写寄存器
*/
void ina219_Write_Register(u8 reg, u16 dat)
{u8 val[2];val[0] = (u8)(dat >> 8);val[1] = (u8)(dat & 0xFF);I2C_WriteNbyte(INA219_I2C_ADDRESS, reg, val, 2);
}/*** @brief   INA219读寄存器
*/
void ina219_Read_Register(u8 reg, u16 *dat)
{u8 val[2];I2C_ReadNbyte(INA219_I2C_ADDRESS, reg, val, 2);*dat = ((u16)(val[0]) << 8) + val[1]; 
}// INA219 Set Calibration 16V/16A(Max) 0.02|?
void ina219_SetCalibration_16V_16A(void)
{u16 configValue;// By default we use a pretty huge range for the input voltage,// which probably isn't the most appropriate choice for system// that don't use a lot of power.  But all of the calculations// are shown below if you want to change the settings.  You will// also need to change any relevant register settings, such as// setting the VBUS_MAX to 16V instead of 32V, etc.// VBUS_MAX     = 16V   (Assumes 16V, can also be set to 32V)// VSHUNT_MAX   = 0.32  (Assumes Gain 8, 320mV, can also be 0.16, 0.08, 0.04)// RSHUNT       = 0.02   (Resistor value in ohms)// 1. Determine max possible current// MaxPossible_I = VSHUNT_MAX / RSHUNT// MaxPossible_I = 16A// 2. Determine max expected current// MaxExpected_I = 16A// 3. Calculate possible range of LSBs (Min = 15-bit, Max = 12-bit)// MinimumLSB = MaxExpected_I/32767// MinimumLSB = 0.00048            (0.48mA per bit)// MaximumLSB = MaxExpected_I/4096// MaximumLSB = 0,00390            (3.9mA per bit)// 4. Choose an LSB between the min and max values//    (Preferrably a roundish number close to MinLSB)// CurrentLSB = 0.00050            (500uA per bit)// 5. Compute the calibration register// Cal = trunc (0.04096 / (Current_LSB * RSHUNT))// Cal = 4096 (0x1000)// ina219_calValue = 0x1000;ina219_calValue = 0x0D90;  //0x1000;// 6. Calculate the power LSB// PowerLSB = 20 * CurrentLSB// PowerLSB = 0.01 (10mW per bit)// 7. Compute the maximum current and shunt voltage values before overflow//// Max_Current = Current_LSB * 32767// Max_Current = 16.3835A before overflow//// If Max_Current > Max_Possible_I then//    Max_Current_Before_Overflow = MaxPossible_I// Else//    Max_Current_Before_Overflow = Max_Current// End If//// Max_ShuntVoltage = Max_Current_Before_Overflow * RSHUNT// Max_ShuntVoltage = 0.32V//// If Max_ShuntVoltage >= VSHUNT_MAX//    Max_ShuntVoltage_Before_Overflow = VSHUNT_MAX// Else//    Max_ShuntVoltage_Before_Overflow = Max_ShuntVoltage// End If// 8. Compute the Maximum Power// MaximumPower = Max_Current_Before_Overflow * VBUS_MAX// MaximumPower = 1.6 * 16V// MaximumPower = 256W// Set multipliers to convert raw current/power valuesina219_current_LSB_uA = 100;     // Current LSB = 500uA per bitina219_power_LSB_mW = 2;         // Power LSB = 10mW per bit = 20 * Current LSB// Set Calibration register to 'Cal' calculated aboveina219_Write_Register(INA219_REG_CALIBRATION, ina219_calValue);// Set Config register to take into account the settings aboveconfigValue = ( INA219_CFG_BVOLT_RANGE_16V | INA219_CFG_SVOLT_RANGE_320MV | INA219_CFG_BADCRES_12BIT_16S_8MS | INA219_CFG_SADCRES_12BIT_16S_8MS | INA219_CFG_MODE_SANDBVOLT_CONTINUOUS );// configValue = ( INA219_CFG_BVOLT_RANGE_16V | INA219_CFG_SVOLT_RANGE_320MV | INA219_CFG_BADCRES_12BIT_32S_17MS | INA219_CFG_SADCRES_12BIT_32S_17MS | INA219_CFG_MODE_SANDBVOLT_CONTINUOUS );ina219_Write_Register(INA219_REG_CONFIG, configValue);
}void ina219_configureRegisters(void)
{delay_ms(15);ina219_SetCalibration_16V_16A();
}s16 ina219_GetBusVoltage_raw(void)
{s16 val;ina219_Read_Register(INA219_REG_BUSVOLTAGE, (u16*)&val);val >>= 3;                      // Shift to the right 3 to drop CNVR and OVFreturn (val);
}s16 ina219_GetCurrent_raw(void)
{s16 val;// Sometimes a sharp load will reset the INA219, which will// reset the cal register, meaning CURRENT and POWER will// not be available ... avoid this by always setting a cal// value even if it's an unfortunate extra stepina219_Write_Register(INA219_REG_CALIBRATION, ina219_calValue);// Now we can safely read the CURRENT register!ina219_Read_Register(INA219_REG_CURRENT, (u16*)&val);return (val);
}s16 ina219_GetBusVoltage_mV(void)
{s16 val;ina219_Read_Register(INA219_REG_BUSVOLTAGE, (u16*)&val);val >>= 3;                      // Shift to the right 3 to drop CNVR and OVFval *= ina219_busVolt_LSB_mV;   // multiply by LSB(4mV)return (s16)(val);
}s32 ina219_GetShuntVoltage_uV(void)
{s32 val;s16 reg;ina219_Read_Register(INA219_REG_SHUNTVOLTAGE, (u16*)&reg);val = (s32)reg * ina219_shuntVolt_LSB_uV;   // multiply by LSB(10uV)return (s32)val;
}s32 ina219_GetCurrent_uA(void)
{s32 val;s16 reg;// Sometimes a sharp load will reset the INA219, which will// reset the cal register, meaning CURRENT and POWER will// not be available ... avoid this by always setting a cal// value even if it's an unfortunate extra stepina219_Write_Register(INA219_REG_CALIBRATION, ina219_calValue);// Now we can safely read the CURRENT register!ina219_Read_Register(INA219_REG_CURRENT, (u16*)&reg);val = (s32)reg * ina219_current_LSB_uA;return (s32)(val);
}s32 ina219_GetPower_mW(void)
{s32 val;s16 reg;// Sometimes a sharp load will reset the INA219, which will// reset the cal register, meaning CURRENT and POWER will// not be available ... avoid this by always setting a cal// value even if it's an unfortunate extra stepina219_Write_Register(INA219_REG_CALIBRATION, ina219_calValue);// Now we can safely read the POWER register!ina219_Read_Register(INA219_REG_POWER, (u16*)&reg);val = (s32)reg * ina219_power_LSB_mW;return (s32)(val);
}void ina219_process(void)
{// TODO: 总线电压 Vin-和GND之间的电压ina219_value.voltage = ina219_GetBusVoltage_mV();log_d("ina219 voltage is:%d(mV)\r\n", ina219_value.voltage);// TODO: 分流电阻两端电压ina219_value.shunt = ina219_GetShuntVoltage_uV();log_d("ina219 shunt   is:%ld(uV)\r\n",ina219_value.shunt);// TODO: 电流ina219_value.current = ina219_GetCurrent_uA();log_d("ina219 current is:%ld(uA)\r\n",ina219_value.current);ina219_value.power = ina219_GetPower_mW();log_d("ina219 power   is:%ld(mW)\r\n",ina219_value.power);			
}void drv_ina219_init(void)
{I2C_InitTypeDef i2c;i2c.I2C_Enable = ENABLE;i2c.I2C_Mode = I2C_Mode_Master;i2c.I2C_Speed = MAIN_Fosc/2/(100000*2+4);i2c.I2C_MS_WDTA = DISABLE;i2c.I2C_SL_MA = ENABLE;I2C_Init(&i2c);// NVIC_I2C_Init(I2C_Mode_Master, ENABLE, Priority_1);  // I2C Master模式可不用开中断P2_MODE_IO_PU(GPIO_Pin_4);P2_MODE_IO_PU(GPIO_Pin_5);I2C_SW(I2C_P24_P25);ina219_configureRegisters();log_d("INA219 Driver Init\n");
}#endif

main.c

main()
{// drv_ina219_init（）;ina219_process();
}

查看全文

http://www.dtcms.com/wzjs/309080.html

沈阳快速建站搭建长沙官网优化公司

吉安网站制作公司排名网站一般怎么推广

软件开发资源网站关键词权重

张家口高新区做网站产品推销

母婴网站源码dede互联网营销顾问是做什么的

怎么用自己的电脑做网站服务器搜狗站长管理平台

网站网络拓扑图淘宝代运营公司排名

高清vpswindows在线看宁波seo推广优化

商城网站网络公司seo技巧课程

从什么网站找做app的代码6个好用的bt种子搜索引擎

网站开发公司的log移动优化课主讲:夫唯老师

企业网站怎么做跟淘宝链接谷歌首页

seo优化谷歌搜索引擎营销优化策略有哪些

大连网站制作流程湖南企业竞价优化服务

网站建设需求调研过程个人开发app可以上架吗

javaweb一个旅游网站怎么做seo网站优化教程

天津交通网站建设seo网站诊断报告

如何自己搭建一个网站百度下载链接

软件测试面试题夫唯seo

做平台交易网站怎么收款品牌营销策划方案怎么做才好

零食店网站建设计划书广州知名网络推广公司

网站丢失怎么解决公司网站的推广

如何做一个好网站广州网站优化费用

提供企业网站建设网站优化排名软件网

十大网站建设排名国际新闻网站

定制美瞳网站建设建立个人网站

沈阳做网站有名公司百度免费

音乐中文网站模板外链购买交易平台

自己做免流网站线上运营推广方案

主流网站开发软件网络营销品牌公司

INA219电流、电压、功率测量芯片应用

简述

芯片引脚

应用电路

寄存器

驱动代码

相关文章：