一级a做爰片就在线看网站简述seo的优化流程
1 概述
本文描述Linux下的dma子系统，包括上层驱动调用方式（consumer），硬件驱动接入（provider）和dma子系统框架。
2 Linux下dma基本软件框架
如下框架大致描述了Linux下的dma子系统软件层次关系，Linux内核提供了dma子系统，向上驱动层提供DMA consumer，驱动开发者只需调用从summer的接口传入对应的dma通道需求信息；向下硬件层提供DMA Provider，该层主要由芯片厂商实现，向dma子系统注册一个chan_device；DMA核心层包括dmaengine、virt-dma和of-dma。
3 dma寄存器配置回顾
（1）配置前准备
1）时钟使能
启用DMA控制器的时钟（如STM32中通过RCC_AHBPeriphClockCmd开启DMA1/DMA2时钟）14。
2）参数确定
传输方向：外设↔存储器或存储器↔存储器18。
数据量：设置单次传输的数据单元数量（如DMA_CNDTRx寄存器）14。
数据宽度：选择字节（8位）、半字（16位）或字（32位）48。
（2）寄存器配置关键步骤
1）地址设置
外设地址：指向外设数据寄存器（如&USART1->DR）14。
存储器地址：指向内存缓冲区（如数组SendBuff[100]() ）14。
地址递增模式：外设地址通常固定，存储器地址按数据宽度递增18。
2）传输模式与优先级
选择循环模式（自动重载数据量）或单次模式（需手动重启）18。
设置通道优先级（高/中/低），冲突时按通道编号仲裁14。
3）中断配置（可选）
使能传输完成/半传输/错误中断，并绑定中断服务函数14。
（3）启动与调试
1）初始化DMA通道
调用初始化函数（如DMA_Init()），加载配置到工作寄存器48。
2）启动传输
使能DMA通道（如DMA_Cmd(DMA1_Channel4, ENABLE)）14。
3）数据监控
通过中断标志位或查询寄存器状态（如DMA_ISR）确认传输完成
4 驱动层调用DMA子系统
上层驱动使用DMA子系统，如下是deepseek生成的一个内存到内存的过程示例
#include <linux/init.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/fs.h>
#include <linux/uaccess.h>
#include <linux/dma-mapping.h>
#include <linux/dmaengine.h>
#include <linux/platform_device.h>#define DEVICE_NAME "dma_example"
#define BUFFER_SIZE 1024
static int major;
static struct dma_chan *dma_chan;
static struct completion dma_complete;
static dma_addr_t src_dma_addr, dst_dma_addr;
static void *src_buffer, *dst_buffer;
// DMA传输完成回调函数
static void dma_callback(void *data)
{complete(&dma_complete);
}
// 字符设备的open方法
static int dma_example_open(struct inode *inode, struct file *filp)
{return 0;
}
// 字符设备的release方法
static int dma_example_release(struct inode *inode, struct file *filp)
{return 0;
}
// 字符设备的write方法，触发DMA传输
static ssize_t dma_example_write(struct file *filp, const char __user *buf, size_t count, loff_t *f_pos)
{struct dma_async_tx_descriptor *desc;dma_cookie_t cookie;// 初始化完成量init_completion(&dma_complete);// 准备DMA描述符desc = dmaengine_prep_dma_memcpy(dma_chan, dst_dma_addr, src_dma_addr, BUFFER_SIZE, DMA_PREP_INTERRUPT);if (!desc) {printk(KERN_ERR "Failed to prepare DMA descriptor\n");return -ENOMEM;}// 设置回调函数desc->callback = dma_callback;desc->callback_param = NULL;// 提交DMA传输cookie = dmaengine_submit(desc);if (dma_submit_error(cookie)) {printk(KERN_ERR "Failed to submit DMA transfer\n");return -EFAULT;}// 启动DMA传输dma_async_issue_pending(dma_chan);// 等待DMA传输完成wait_for_completion(&dma_complete);return count;
}
// 字符设备的文件操作结构体
static struct file_operations fops = {.owner = THIS_MODULE,.open = dma_example_open,.release = dma_example_release,.write = dma_example_write,
};
// 驱动模块初始化函数
static int __init dma_example_init(void)
{// 注册字符设备major = register_chrdev(0, DEVICE_NAME, &fops);if (major < 0) {printk(KERN_ALERT "Failed to register character device\n");return major;}printk(KERN_INFO "DMA example driver registered with major number %d\n", major);// 分配DMA通道dma_chan = dma_request_chan(NULL, "memcpy");if (!dma_chan) {printk(KERN_ERR "Failed to request DMA channel\n");unregister_chrdev(major, DEVICE_NAME);return -ENODEV;}// 分配源和目的缓冲区src_buffer = dma_alloc_coherent(NULL, BUFFER_SIZE, &src_dma_addr, GFP_KERNEL);dst_buffer = dma_alloc_coherent(NULL, BUFFER_SIZE, &dst_dma_addr, GFP_KERNEL);if (!src_buffer || !dst_buffer) {printk(KERN_ERR "Failed to allocate DMA buffers\n");dma_release_channel(dma_chan);unregister_chrdev(major, DEVICE_NAME);return -ENOMEM;}// 初始化源缓冲区memset(src_buffer, 0xAA, BUFFER_SIZE);return 0;
}
// 驱动模块退出函数
static void __exit dma_example_exit(void)
{// 释放DMA缓冲区dma_free_coherent(NULL, BUFFER_SIZE, src_buffer, src_dma_addr);dma_free_coherent(NULL, BUFFER_SIZE, dst_buffer, dst_dma_addr);// 释放DMA通道dma_release_channel(dma_chan);// 注销字符设备unregister_chrdev(major, DEVICE_NAME);printk(KERN_INFO "DMA example driver unregistered\n");
}
module_init(dma_example_init);
module_exit(dma_example_exit);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Your Name");
MODULE_DESCRIPTION("A simple DMA example driver");先请求一个dma通道（示例请求了memcpy名的通道），使用dma_alloc_coherent申请了两个拷贝内存，之后由用户调用write开始dma配置后启动， dmaengine_prep_dma_memcpy实际上调用到了硬件IP实现的接口，主要配置了寄存器内存地址与模式（后续章节分析），之后调用 dmaengine_submit，该接口也是调用到硬件IP接口层实现的接口，而该接口会将当前descp提交请求加入到virt-dma维护的node链表中，descp维护一个callback。最后调用dma_async_issue_pending启动传输，该接口配置dma寄存器启动传输，硬件终端产生时，硬件层将在中断中启动一个事先准备好的tasklet，用来回调上层传入的callback回调（从virt-dma维护的node链表中取出callback）。
上述示例用了dma_alloc_coherent分配内存，该方式主要用来解决缓存一致性问题，用于分配一块内存，并同时将其映射为DMA可以访问的形式。 这种内存区域具有一致性，意味着无论是在CPU还是DMA控制器看来，该内存的内容都是同步的。 这对于需要频繁读写且要求一致性的场景非常有用。
对于已有内存，使用另外一个接口：
struct device *dev;
void *cpu_addr = kmalloc(size, GFP_KERNEL); // 分配一个缓冲区
dma_addr_t dma_handle;
// 映射缓冲区
/*
映射单个缓冲区：dma_map_single 用于将一个已经分配好的内存缓冲区映射为DMA可以访问的形式。这个函数通常用于临时或一次性使用的缓冲区。
*/
dma_handle = dma_map_single(dev, cpu_addr, size, DMA_TO_DEVICE);
if (dma_mapping_error(dev, dma_handle)) {printk(KERN_ERR "DMA mapping error\n");kfree(cpu_addr);return -EINVAL;
}
// 使用dma_handle进行DMA传输...
// 解除映射
dma_unmap_single(dev, dma_handle, size, DMA_TO_DEVICE);
// 释放缓冲区
kfree(cpu_addr);
除了内存到内存，还有内存到设备的dma传输；上述示例使用dmaengine_prep_dma_memcpy，用于内存到内存传输，该函数用于配置内存到内存的数据传输；它适用于需要在两个内存地址之间直接传输数据的情况，而不需要通过任何外部设备。对于内存到设备，一般用dmaengine_prep_slave_sg，如下示例：
int sample_request_dma(void)
{struct dma_chan *chan;struct dma_async_tx_descriptor *tx;dma_cookie_t cookie;struct scatterlist sg;// 请求DMA通道chan = dma_request_chan(dev, "my_dma_channel");if (IS_ERR(chan)) {// 处理错误}// 准备DMA传输tx = dmaengine_prep_slave_sg(chan, &sg, 1, DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT | DMA_CTRL_ACK);if (!tx) {// 处理错误}// 设置传输完成回调tx->callback = my_dma_callback;tx->callback_param = my_param;// 提交传输cookie = tx->tx_submit(tx);if (dma_submit_error(cookie)) {// 处理错误}// 启动传输dma_async_issue_pending(chan);// 等待传输完成dma_sync_wait(chan, cookie);// 释放DMA通道dma_release_channel(chan);return 0;
}5 硬件IP注册一个DMA provider
以stm32的驱动为例子drivers/dma/stm32-dma.c
Stm32设备内容如下：
Stm32有两个dma IP，每个dma有8个通道，每个通道各自有一个中断，如下是设备树描述的硬件信息：
dma1: dma-controller@40026000 {compatible = "st,stm32-dma";reg = <0x40026000 0x400>;
//每个dma对应一个中断号interrupts = <11>,<12>,<13>,<14>,<15>,<16>,<17>,<47>;clocks = <&rcc 0 STM32F7_AHB1_CLOCK(DMA1)>;#dma-cells = <4>;status = "disabled";};dma2: dma-controller@40026400 {compatible = "st,stm32-dma";reg = <0x40026400 0x400>;interrupts = <56>,<57>,<58>,<59>,<60>,<68>,<69>,<70>;clocks = <&rcc 0 STM32F7_AHB1_CLOCK(DMA2)>;#dma-cells = <4>;st,mem2mem;status = "disabled";};驱动实现在drivers/dma/stm32-dma.c
驱动probe函数主要实现了向DMA子系统注册一个provider:
static const struct of_device_id stm32_dma_of_match[] = {{ .compatible = "st,stm32-dma", },{ /* sentinel */ },
};
MODULE_DEVICE_TABLE(of, stm32_dma_of_match);
static int stm32_dma_probe(struct platform_device *pdev)
{struct stm32_dma_chan *chan;struct stm32_dma_device *dmadev;struct dma_device *dd;const struct of_device_id *match;struct resource *res;struct reset_control *rst;int i, ret;...dmadev = devm_kzalloc(&pdev->dev, sizeof(*dmadev), GFP_KERNEL);...dmadev->mem2mem = of_property_read_bool(pdev->dev.of_node,"st,mem2mem");
...
//当前dma设备能力配置dma_cap_set(DMA_SLAVE, dd->cap_mask);dma_cap_set(DMA_PRIVATE, dd->cap_mask);
dma_cap_set(DMA_CYCLIC, dd->cap_mask);
//根据前面能力配置，实现相关的回调，这些回调将被上层驱动通过指针方式直接调用
//根据芯片dma ip特性不同，在用户获取一个chan时，该接口被调用，用于对应硬件chan的初始化
dd->device_alloc_chan_resources = stm32_dma_alloc_chan_resources;
//释放
dd->device_free_chan_resources = stm32_dma_free_chan_resources;
//获取发送的状态结果
dd->device_tx_status = stm32_dma_tx_status;
//dd->device_issue_pending = stm32_dma_issue_pending;dd->device_prep_slave_sg = stm32_dma_prep_slave_sg;dd->device_prep_dma_cyclic = stm32_dma_prep_dma_cyclic;dd->device_config = stm32_dma_slave_config;dd->device_terminate_all = stm32_dma_terminate_all;dd->device_synchronize = stm32_dma_synchronize;dd->src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |BIT(DMA_SLAVE_BUSWIDTH_2_BYTES) |BIT(DMA_SLAVE_BUSWIDTH_4_BYTES);dd->dst_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |BIT(DMA_SLAVE_BUSWIDTH_2_BYTES) |BIT(DMA_SLAVE_BUSWIDTH_4_BYTES);dd->directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV);dd->residue_granularity = DMA_RESIDUE_GRANULARITY_BURST;dd->copy_align = DMAENGINE_ALIGN_32_BYTES;dd->max_burst = STM32_DMA_MAX_BURST;dd->descriptor_reuse = true;dd->dev = &pdev->dev;INIT_LIST_HEAD(&dd->channels);if (dmadev->mem2mem) {//实现内存到内存的dma拷贝接口dma_cap_set(DMA_MEMCPY, dd->cap_mask);dd->device_prep_dma_memcpy = stm32_dma_prep_dma_memcpy;dd->directions |= BIT(DMA_MEM_TO_MEM);}for (i = 0; i < STM32_DMA_MAX_CHANNELS; i++) {//初始化每个通道，包括绑定每个通道到一个虚拟通道中chan = &dmadev->chan[i];chan->id = i;chan->vchan.desc_free = stm32_dma_desc_free;vchan_init(&chan->vchan, dd);}ret = dma_async_device_register(dd);//注册到DMA子系统中if (ret)goto clk_free;for (i = 0; i < STM32_DMA_MAX_CHANNELS; i++) {chan = &dmadev->chan[i];ret = platform_get_irq(pdev, i);...chan->irq = ret;
//为每个通道中断注册好中断服务，主要是回调用户的回调，通知用户dma已完成ret = devm_request_irq(&pdev->dev, chan->irq,stm32_dma_chan_irq, 0,dev_name(chan2dev(chan)), chan);...
}
//将当前dma注册到设备管理控制模块中，用户可以通过调用设备树接口方式来获取dma通道进而使用相应控制接口ret = of_dma_controller_register(pdev->dev.of_node,stm32_dma_of_xlate, dmadev);...return 0;dma_async_device_unregister(dd);
... return ret;
}以上是一个DMA注册provider的一般过程，回调接口流程后续章节介绍。
6 追溯驱动调用接口（DMA子系统consumer接口）
6.1 dma_request_chan/dma_request_channel
该接口将调用硬件层回调，stm的dma ip驱动，device_alloc_chan_resources做了channel的初始化：
dma_request_chan
=>find_candidate
==>dma_chan_get
===>device_alloc_chan_resources
struct dma_chan *dma_request_chan(struct device *dev, const char *name)
{struct dma_device *d, *_d;struct dma_chan *chan = NULL;/* If device-tree is present get slave info from here */
/*根据名称获取设备对应定义的channel，例如这里name是tx，设备树定义如下：
i2s0: i2s@1011a000 {...dmas = <&dmac1_s 6>, <&dmac1_s 7>;dma-names = "tx", "rx";...
};
此时tx将根据dmas标签获取到dma节点的dmac1_s第6个通道。
*/if (dev->of_node)chan = of_dma_request_slave_channel(dev->of_node, name);
....
/* Try to find the channel via the DMA filter map(s) */
/*
上述代码中查询dma通道失败，则尝试用dma的map映射关系来查询获取，从dma_device_list中获取dma，在查找具体的通道，dma_device_list硬件在注册的时候被放到该链表中。这里需要硬件驱动实现好dma_device里的filter，上层驱动才能根据channel名称找到。
*/mutex_lock(&dma_list_mutex);list_for_each_entry_safe(d, _d, &dma_device_list, global_node) {dma_cap_mask_t mask;
//匹配dev名称和channel名称const struct dma_slave_map *map = dma_filter_match(d, name, dev);if (!map)continue;
//查询slave能力的channeldma_cap_zero(mask);dma_cap_set(DMA_SLAVE, mask);chan = find_candidate(d, &mask, d->filter.fn, map->param);if (!IS_ERR(chan))break;}mutex_unlock(&dma_list_mutex);...
found:
...chan->name = kasprintf(GFP_KERNEL, "dma:%s", name);if (!chan->name)return chan;....return chan;
}dma_request_channel删除了根据设备树名称获取通道，根据传入的设备引用的dma设备节点与注册好的dma设备节点是否一致，来获取当前slave通道。
#define dma_request_channel(mask, x, y) \__dma_request_channel(&(mask), x, y, NULL)
struct dma_chan *__dma_request_channel(const dma_cap_mask_t *mask,dma_filter_fn fn, void *fn_param,struct device_node *np)
{struct dma_device *device, *_d;struct dma_chan *chan = NULL;
...list_for_each_entry_safe(device, _d, &dma_device_list, global_node) {/* Finds a DMA controller with matching device node */if (np && device->dev->of_node && np != device->dev->of_node)continue;chan = find_candidate(device, mask, fn, fn_param);...}...return chan;
}6.2 dmaengine_prep_dma_memcpy/dmaengine_prep_slave_sg
dmaengine_prep_dma_memcpy最终回调到DMA硬件驱动接口
static inline struct dma_async_tx_descriptor *dmaengine_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src,size_t len, unsigned long flags)
{....return chan->device->device_prep_dma_memcpy(chan, dest, src,len, flags);
}Stm32硬件驱动中
static int stm32_dma_probe(struct platform_device *pdev)
{
...if (dmadev->mem2mem) {dma_cap_set(DMA_MEMCPY, dd->cap_mask);dd->device_prep_dma_memcpy = stm32_dma_prep_dma_memcpy;dd->directions |= BIT(DMA_MEM_TO_MEM);}
...
}该硬件接口主要实现对dma搬运地址的配置，模式的配置，准备好启动dma搬运
static struct dma_async_tx_descriptor *stm32_dma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest,dma_addr_t src, size_t len, unsigned long flags)
{struct stm32_dma_chan *chan = to_stm32_dma_chan(c);...desc = kzalloc(struct_size(desc, sg_req, num_sgs), GFP_NOWAIT);if (!desc)return NULL;
threshold = chan->threshold;
//配置发送长度for (offset = 0, i = 0; offset < len; offset += xfer_count, i++) {xfer_count = min_t(size_t, len - offset,STM32_DMA_ALIGNED_MAX_DATA_ITEMS);/* Compute best burst size */max_width = DMA_SLAVE_BUSWIDTH_1_BYTE;best_burst = stm32_dma_get_best_burst(len, STM32_DMA_MAX_BURST,threshold, max_width);dma_burst = stm32_dma_get_burst(chan, best_burst);stm32_dma_clear_reg(&desc->sg_req[i].chan_reg);//写入寄存器desc->sg_req[i].chan_reg.dma_scr =STM32_DMA_SCR_DIR(STM32_DMA_MEM_TO_MEM) |STM32_DMA_SCR_PBURST(dma_burst) |STM32_DMA_SCR_MBURST(dma_burst) |STM32_DMA_SCR_MINC |STM32_DMA_SCR_PINC |STM32_DMA_SCR_TCIE |STM32_DMA_SCR_TEIE;desc->sg_req[i].chan_reg.dma_sfcr |= STM32_DMA_SFCR_MASK;desc->sg_req[i].chan_reg.dma_sfcr |=STM32_DMA_SFCR_FTH(threshold);desc->sg_req[i].chan_reg.dma_spar = src + offset;desc->sg_req[i].chan_reg.dma_sm0ar = dest + offset;desc->sg_req[i].chan_reg.dma_sndtr = xfer_count;desc->sg_req[i].len = xfer_count;}desc->num_sgs = num_sgs;
desc->cyclic = false;
//准备发送相关数据return vchan_tx_prep(&chan->vchan, &desc->vdesc, flags);
}
static inline struct dma_async_tx_descriptor *vchan_tx_prep(struct virt_dma_chan *vc,struct virt_dma_desc *vd, unsigned long tx_flags)
{...vd->tx.tx_submit = vchan_tx_submit;//提供上层触发dma搬运的回调vd->tx.desc_free = vchan_tx_desc_free;//上层调用释放...return &vd->tx;
}同样，dmaengine_prep_slave_sg最终调用到硬件驱动接口。
static inline struct dma_async_tx_descriptor *dmaengine_prep_slave_sg(struct dma_chan *chan, struct scatterlist *sgl, unsigned int sg_len,enum dma_transfer_direction dir, unsigned long flags)
{...return chan->device->device_prep_slave_sg(chan, sgl, sg_len,dir, flags, NULL);
}
static struct dma_async_tx_descriptor *stm32_dma_prep_slave_sg(struct dma_chan *c, struct scatterlist *sgl,u32 sg_len, enum dma_transfer_direction direction,unsigned long flags, void *context)
{struct stm32_dma_chan *chan = to_stm32_dma_chan(c);struct stm32_dma_desc *desc;struct scatterlist *sg;enum dma_slave_buswidth buswidth;u32 nb_data_items;int i, ret;....desc = kzalloc(struct_size(desc, sg_req, sg_len), GFP_NOWAIT);if (!desc)return NULL;
...
//配置发送参数for_each_sg(sgl, sg, sg_len, i) {ret = stm32_dma_set_xfer_param(chan, direction, &buswidth,sg_dma_len(sg),sg_dma_address(sg));if (ret < 0)goto err;desc->sg_req[i].len = sg_dma_len(sg);nb_data_items = desc->sg_req[i].len / buswidth;if (nb_data_items > STM32_DMA_ALIGNED_MAX_DATA_ITEMS) {dev_err(chan2dev(chan), "nb items not supported\n");goto err;}stm32_dma_clear_reg(&desc->sg_req[i].chan_reg);desc->sg_req[i].chan_reg.dma_scr = chan->chan_reg.dma_scr;desc->sg_req[i].chan_reg.dma_sfcr = chan->chan_reg.dma_sfcr;desc->sg_req[i].chan_reg.dma_spar = chan->chan_reg.dma_spar;desc->sg_req[i].chan_reg.dma_sm0ar = sg_dma_address(sg);desc->sg_req[i].chan_reg.dma_sm1ar = sg_dma_address(sg);desc->sg_req[i].chan_reg.dma_sndtr = nb_data_items;}desc->num_sgs = sg_len;
desc->cyclic = false;
//准备发送数据return vchan_tx_prep(&chan->vchan, &desc->vdesc, flags);
...}6.3 dmaengine_submit/tx->tx_submi
这两个接口，最终调用了由dmaengine_prep_dma_memcpy/dmaengine_prep_slave_sg返回的desc中tx_submit，该会调用在这两个接口中赋值（dmaengine_prep_dma_memcpy/dmaengine_prep_slave_sg中介绍过）。
tx->tx_submit(tx);
static inline dma_cookie_t dmaengine_submit(struct dma_async_tx_descriptor *desc)
{return desc->tx_submit(desc);
}在stm32硬件驱动中实现如下，最终将发送的节点放到node链表中。
dma_cookie_t vchan_tx_submit(struct dma_async_tx_descriptor *tx)
{struct virt_dma_chan *vc = to_virt_chan(tx->chan);struct virt_dma_desc *vd = to_virt_desc(tx);。。。cookie = dma_cookie_assign(tx);list_move_tail(&vd->node, &vc->desc_submitted);...return cookie;
}什么时候这个链表被拿出来，启动dma搬运的？这个过程由用户调用接口dma_async_issue_pending来触发。
6.4 dma_async_issue_pending
static inline void dma_async_issue_pending(struct dma_chan *chan)
{chan->device->device_issue_pending(chan);
}该接口同样回调到dma硬件驱动的接口，在stm32硬件驱动文件中：
dd->device_issue_pending = stm32_dma_issue_pending;
static void stm32_dma_issue_pending(struct dma_chan *c)
{
...
//将当前需要启动的channel对象，放到desc_issued链表，并查询是否需要启动dmaif (vchan_issue_pending(&chan->vchan) && !chan->desc && !chan->busy) {dev_dbg(chan2dev(chan), "vchan %pK: issued\n", &chan->vchan);stm32_dma_start_transfer(chan);//启动发送}...
}
static void stm32_dma_start_transfer(struct stm32_dma_chan *chan)
{struct stm32_dma_device *dmadev = stm32_dma_get_dev(chan);struct virt_dma_desc *vdesc;struct stm32_dma_sg_req *sg_req;struct stm32_dma_chan_reg *reg;u32 status;
int ret;
//发送前配置寄存器先关闭dmaret = stm32_dma_disable_chan(chan);if (ret < 0)return;
if (!chan->desc) {
//在这里根据vchan从node链表获取前面放入的对象vdesc = vchan_next_desc(&chan->vchan);if (!vdesc)return;list_del(&vdesc->node);chan->desc = to_stm32_dma_desc(vdesc);//转成实际chanchan->next_sg = 0;}
...
//写寄存器stm32_dma_write(dmadev, STM32_DMA_SCR(chan->id), reg->dma_scr);stm32_dma_write(dmadev, STM32_DMA_SPAR(chan->id), reg->dma_spar);stm32_dma_write(dmadev, STM32_DMA_SM0AR(chan->id), reg->dma_sm0ar);stm32_dma_write(dmadev, STM32_DMA_SFCR(chan->id), reg->dma_sfcr);stm32_dma_write(dmadev, STM32_DMA_SM1AR(chan->id), reg->dma_sm1ar);stm32_dma_write(dmadev, STM32_DMA_SNDTR(chan->id), reg->dma_sndtr);...
//发送stm32_dma_write(dmadev, STM32_DMA_SCR(chan->id), reg->dma_scr);
...}
6.4 dma_sync_wait
Dma完成同步接口，调用该接口等待dma传输完成，也可以通过回调获取dma传输结果（后续章节分析）。
enum dma_status dma_sync_wait(struct dma_chan *chan, dma_cookie_t cookie)
{enum dma_status status;unsigned long dma_sync_wait_timeout = jiffies + msecs_to_jiffies(5000);//重新使能发送，确保使能过dma，可见用户可以直接调用该接口，不需要手调 dma_async_issue_pendingdma_async_issue_pending(chan);do {status = dma_async_is_tx_complete(chan, cookie, NULL, NULL);if (time_after_eq(jiffies, dma_sync_wait_timeout)) {dev_err(chan->device->dev, "%s: timeout!\n", __func__);return DMA_ERROR;}if (status != DMA_IN_PROGRESS)break;
//cpu休眠cpu_relax();} while (1);return status;
}
static inline enum dma_status dma_async_is_tx_complete(struct dma_chan *chan,dma_cookie_t cookie, dma_cookie_t *last, dma_cookie_t *used)
{
...//调用硬件实现的接口device_tx_statusstatus = chan->device->device_tx_status(chan, cookie, &state);...return status;
}
static enum dma_status stm32_dma_tx_status(struct dma_chan *c,dma_cookie_t cookie,struct dma_tx_state *state)
{... //根据硬件状态返回if (status == DMA_COMPLETE || !state)return status;...return status;
}
6.5 dma子系统如何通过回调通知用户dma状态
如下一个dma驱动应用大致调用接口流程，中间配置了callback。
static ssize_t dma_example_write(struct file *filp, const char __user *buf, size_t count, loff_t *f_pos)
{
struct dma_async_tx_descriptor *desc;
...desc = dmaengine_prep_dma_memcpy(dma_chan, dst_dma_addr, src_dma_addr, BUFFER_SIZE, DMA_PREP_INTERRUPT);...// 设置回调函数desc->callback = dma_callback;desc->callback_param = NULL;cookie = dmaengine_submit(desc);...dma_async_issue_pending(dma_chan);
...}这里配置的 dma_callback，将在dma传输完成后，dma触发中断开启worktask调用。
在stm32dma硬件驱动(drivers/dma/stm32-dma.c)probe初始化过程中，为每个dma通道各自创建了一个taskwork：
static int stm32_dma_probe(struct platform_device *pdev)
{
...for (i = 0; i < STM32_DMA_MAX_CHANNELS; i++) {chan = &dmadev->chan[i];chan->id = i;chan->vchan.desc_free = stm32_dma_desc_free;vchan_init(&chan->vchan, dd);
}
...
}vchan_init实现在drivers/dma/virt-dma.c：
void vchan_init(struct virt_dma_chan *vc, struct dma_device *dmadev)
{dma_cookie_init(&vc->chan);...tasklet_setup(&vc->task, vchan_complete);//在这里创建工作线程，配置回调...list_add_tail(&vc->chan.device_node, &dmadev->channels);//将每个channel放到channels链表
}vchan_complete主要实现了对用户传入的callback进行回调
static void vchan_complete(struct tasklet_struct *t)
{struct virt_dma_chan *vc = from_tasklet(vc, t, task);struct virt_dma_desc *vd, *_vd;struct dmaengine_desc_callback cb;LIST_HEAD(head);...vd = vc->cyclic;if (vd) {vc->cyclic = NULL;
//tx是用户调用submit回调传进来的，这里将tx里回调信息赋值给cbdmaengine_desc_get_callback(&vd->tx, &cb);} else {memset(&cb, 0, sizeof(cb));}
...
//回调用户回调接口
dmaengine_desc_callback_invoke(&cb, &vd->tx_result);
//下面逻辑跟上面一样，这里从node链表里取出用户配置的所有callback，即通知所有注册callback的上层用户。list_for_each_entry_safe(vd, _vd, &head, node) {dmaengine_desc_get_callback(&vd->tx, &cb);list_del(&vd->node);dmaengine_desc_callback_invoke(&cb, &vd->tx_result);vchan_vdesc_fini(vd);}
}重新看下callback的下发，前面应用调用流程知道callback配置到desc中：
static ssize_t dma_example_write(struct file *filp, const char __user *buf, size_t count, loff_t *f_pos)
{
struct dma_async_tx_descriptor *desc;
...// 设置回调函数desc->callback = dma_callback;desc->callback_param = NULL;cookie = dmaengine_submit(desc);...}调用到的下一层回调
dma_cookie_t vchan_tx_submit(struct dma_async_tx_descriptor *tx)
{struct virt_dma_chan *vc = to_virt_chan(tx->chan);struct virt_dma_desc *vd = to_virt_desc(tx);//vd和tx绑定，后续能根据vd找到tx回调...
list_move_tail(&vd->node, &vc->desc_submitted);//加入node链表
...
}上述分析回调被调用流程，需要触发工作线程才能回调 vchan_complete来完成回调，工作线程的触发是在中断完成，在硬件驱动初始化中，会对每个channel的中断进行注册绑定一个服务函数：
static int stm32_dma_probe(struct platform_device *pdev)
{
...
for (i = 0; i < STM32_DMA_MAX_CHANNELS; i++) {chan = &dmadev->chan[i];ret = platform_get_irq(pdev, i);...chan->irq = ret;ret = devm_request_irq(&pdev->dev, chan->irq,stm32_dma_chan_irq, 0,dev_name(chan2dev(chan)), chan);...}
...}中断服务函数如下：
static irqreturn_t stm32_dma_chan_irq(int irq, void *devid)
{...if (status & STM32_DMA_TCI) {//dma channel完成标志stm32_dma_irq_clear(chan, STM32_DMA_TCI);if (scr & STM32_DMA_SCR_TCIE)stm32_dma_handle_chan_done(chan);status &= ~STM32_DMA_TCI;}....return IRQ_HANDLED;
}完成函数如下，如果支持循环搬运，持续配置dma寄存器工作，完成情况下，调用vchan_cookie_complete
static void stm32_dma_handle_chan_done(struct stm32_dma_chan *chan)
{if (chan->desc) {if (chan->desc->cyclic) {vchan_cyclic_callback(&chan->desc->vdesc);chan->next_sg++;stm32_dma_configure_next_sg(chan);} else {chan->busy = false;if (chan->next_sg == chan->desc->num_sgs) {vchan_cookie_complete(&chan->desc->vdesc);chan->desc = NULL;}stm32_dma_start_transfer(chan);}}
}vchan_cookie_complete实现在drivers/dma/virt-dma.h：
static inline void vchan_cookie_complete(struct virt_dma_desc *vd)
{...tasklet_schedule(&vc->task);//调度工作线程
}7 几个关键数据结构关系
如下关系图大致描述了几个关键的数据结构关系，dma_device_list维护了多个dma_device，每个dma IP被抽象成一个dma_device，同时被struct_dma_chan引用，子系统中用virt_dma_chan来表达一个物理channel，每个channel对应一个vchan，同时为用户生成了该dma属性结构体struct virt_dma_desc。
