苍南网站建设shaokysem是做什么的
1-设计流程
● 了解cordic 算法原理，公式，模式，伸缩因子，旋转方向等，推荐以下链接视频了解 cordic 算法。哔哩哔哩-cordic算法原理讲解
● 用matlab 或者 c 实现一遍算法
● 在FPGA中用 verilog 实现，注意使用有符号变量以及小数点定点化处理
备注：
在verilog 需要用 ram 存储的值：列举了13次迭代的tan值和对应角度；
2-RTL
分享自己写的一个cordic rtl ：
2-1 测试代码 ,测试 一二三四象限内角度的sin cos 值。
module test_my_cordic(input i_clk,input i_rst);reg signed [31:0] r_angle;
reg r_valid ;wire w_ready;
wire signed [31:0] r_x = 39796;
wire signed [31:0] r_y = 0;(*dont_touch = "true"*)
my_cordic inst_my_cordic
(.i_clk (i_clk),.i_rst (i_rst),.i_iteration_count (16), //设置迭代次数 ，最大16次.i_setx (r_x),.i_sety (r_y),.i_set_angle (r_angle),.i_valid (r_valid),.o_sin (),.o_cos (),.o_valid (),.o_ready (w_ready)
);/* 测试 第四象限 0 ~ -90°
always @ (posedge i_clk or posedge i_rst)
beginif (i_rst) beginr_angle <= 0;end else if (r_angle == -5898240 && w_ready) beginr_angle <= 0; end else if (w_ready && r_valid) beginr_angle <= r_angle - 655360; end else beginr_angle <= r_angle; end
end
*/// 测试 第一象限 0 ~ 90°
always @ (posedge i_clk or posedge i_rst)
beginif (i_rst) beginr_angle <= 0;end else if (r_angle == 5898240 && w_ready) beginr_angle <= 0; end else if (w_ready && r_valid) beginr_angle <= r_angle + 655360; end else beginr_angle <= r_angle; end
end/* //测试 第三象限 -180 ~ -90°
always @ (posedge i_clk or posedge i_rst)
beginif (i_rst) beginr_angle <= -11796480;end else if (r_angle == -5898240 && w_ready) beginr_angle <= -11796480; end else if (w_ready && r_valid) beginr_angle <= r_angle + 655360; end else beginr_angle <= r_angle; end
end
*//*// 测试 第二象限 90° ~ 180 °
always @ (posedge i_clk or posedge i_rst)
beginif (i_rst) beginr_angle <= 5898240;end else if (r_angle == 11796480 && w_ready) beginr_angle <= 0; end else if (w_ready && r_valid) beginr_angle <= r_angle + 655360; end else beginr_angle <= r_angle; end
end
*/always @ (posedge i_clk or posedge i_rst)
beginif (i_rst) r_valid <= 0;else if (w_ready && r_valid)r_valid <= 0;else if (w_ready)r_valid <= 1; else r_valid <= 0;
endendmodule
2-2 核心代码：
//运算公式：
//x(i+1) = x(i) - y(i) * di * 2^(-i)
//y(i+1) = y(i) + x(i) * di * 2^(-i)
//z(i+1) = z(i) - arctan(di * 2^(-i))
//author ： 技术小白爱FPGA
//备注：cordic 算法，旋转模式，迭代次数固定 16次，可以自己任意设置，最大16次module my_cordic (input i_clk ,input i_rst ,input [4:0] i_iteration_count ,input signed [31:0] i_setx ,input signed [31:0] i_sety ,input signed [31:0] i_set_angle ,input i_valid ,output signed [31:0] o_sin ,output signed [31:0] o_cos ,output o_valid ,output o_ready );wire signed [31:0] r_arctan [0:15];
wire r_di ;reg signed [31:0] r_sin;
reg signed [31:0] r_cos;
reg signed [31:0] r_setx ;
reg signed [31:0] r_sety ;
reg signed [31:0] r_angle ;
reg [4:0] r_count;
reg r_run_cal;
reg ro_valid ;
reg ro_ready ;
reg [1:0] r_site;assign o_sin = r_sin;
assign o_cos = r_cos;
assign o_ready = ro_ready;
assign o_valid = ro_valid;//存储 arctan 值，整体表示-----扩大2^16倍数，相当于将小数点定在16bit位置上
assign r_arctan[0] = 2949120;
assign r_arctan[1] = 1740967;
assign r_arctan[2] = 919879;
assign r_arctan[3] = 466945;
assign r_arctan[4] = 234378;
assign r_arctan[5] = 117303;
assign r_arctan[6] = 58666;
assign r_arctan[7] = 29334;
assign r_arctan[8] = 14667;
assign r_arctan[9] = 7333;
assign r_arctan[10]= 3666;
assign r_arctan[11]= 1833;
assign r_arctan[12]= 916;
assign r_arctan[13]= 458;
assign r_arctan[14]= 229;
assign r_arctan[15]= 114;//判断旋转的方向
assign r_di = (r_angle > 0 && r_run_cal)?1:0;//运算迭代 >>> --- > 算数右移，不改变符号位； 如果使用 >> ,移位，高位补0；
always @ (posedge i_clk)
beginif (i_valid) beginr_setx <= i_setx;r_sety <= i_sety;endelse if (r_run_cal && r_di ) beginr_setx <= r_setx - (r_sety >>> r_count);r_sety <= r_sety + (r_setx >>> r_count); end else if (r_run_cal && !r_di) beginr_setx <= r_setx + (r_sety >>> r_count);r_sety <= r_sety - (r_setx >>> r_count); end
end//旋转角度的迭代,输入角度的象限处理
always @ (posedge i_clk )
begin// 处理 一四象限 -90° ~ 90°if (i_valid && (i_set_angle >= -5898240 && i_set_angle <= 5898240 ) ) beginr_angle <= i_set_angle;r_site <= 2'b00;// 处理 二象限 90° ~ 180°end else if (i_valid && (i_set_angle > 5898240 && i_set_angle <= 11796480 )) beginr_angle <= 11796480 - i_set_angle;r_site <= 2'b10;// 处理 三象限 -180° ~ -90°end else if (i_valid && (i_set_angle >= -11796480 && i_set_angle < -5898240 )) beginr_angle <= -11796480 - i_set_angle ;r_site <= 2'b11;end else if (r_di && r_run_cal) beginr_angle <= r_angle - r_arctan[r_count]; endelse if (!r_di && r_run_cal) beginr_angle <= r_angle + r_arctan[r_count]; end else beginr_angle <= r_angle;r_site <= r_site ;end
end//迭代运算次数
always @ (posedge i_clk or posedge i_rst)
beginif (i_rst) beginr_count <= 0;end else if (r_count == i_iteration_count -1) beginr_count <= 0;endelse if (r_run_cal) beginr_count <= r_count + 1;end
end//迭代运算标志
always @ (posedge i_clk or posedge i_rst)
beginif (i_rst) beginr_run_cal <= 0;endelse if (r_count == i_iteration_count -1) beginr_run_cal <= 0; endelse if(i_valid) beginr_run_cal <= 1; endelse beginr_run_cal <= r_run_cal; end
end//最终输出的 sin cos 值
always @ (posedge i_clk or posedge i_rst)
beginif (i_rst) beginr_sin <= 0;r_cos <= 0;endelse if (r_site == 2'b00 && r_count == i_iteration_count -1) beginr_sin <= r_sety;r_cos <= r_setx; end else if (r_site == 2'b10 && r_count == i_iteration_count -1) beginr_sin <= r_sety;r_cos <= -r_setx; end else if (r_site == 2'b11 && r_count == i_iteration_count -1) beginr_sin <= r_sety;r_cos <= -r_setx; end
endalways @ (posedge i_clk or posedge i_rst)
beginif (i_rst) beginro_ready <= 1;endelse if (i_valid || r_run_cal) beginro_ready <= 0; end else beginro_ready <= 1;end
end//最终输出的 sin cos valid 信号
always @ (posedge i_clk or posedge i_rst)
beginif (i_rst) ro_valid <= 0;else if (r_count == i_iteration_count -1)ro_valid <= 1; else ro_valid <= 0;
endendmodule
2-3 tb仿真代码
module tb_cordic();reg i_clk;
reg i_rst;initial begin i_clk = 0;i_rst = 1;#100@(posedge i_clk)i_rst =0;
endalways #10 i_clk = ~i_clk;test_my_cordic inst_test_my_cordic (.i_clk(i_clk), .i_rst(i_rst));endmodule
3-仿真
a. 首先 有符号的信号需要设置 小数点位数，如下图所示：
b. 以第一象限为例子：0 ~ 90°
c. 运算处理 持续周期 就是 迭代次数：
d. 可借助 计算机科学模式验证结果：
4-可优化空间
● r_ange逻辑级数；
● 360°以内，高于180°和小于-180°处理
● 迭代运算拆成流水线形式；
● 加上向量模式
● 整体其它逻辑的优化